Jump to content
SAU Community

R33 GTST wont start with Haltech ECU

Johnsontke

By Johnsontke,
in Engines & Forced Induction

 Share

Recommended Posts

Johnsontke Rookie

Johnsontke

Posted
Posted (edited)

R33 GTST wont start with Haltech ECU

Hey there,

So i'm new to this forum and i did some looking around to see if i could find anything similar to my problem and there were a couple but not 100%. 

Anyways the problem i'm having is i bought a haltech platinum sport 2000 (the plug n play) and i installed it simple enough. 

While i was doing this i also installed some nismo 555cc injectors. The base map that comes with the ecu is set for the stock injectors.

now after adjusting the fuel map the car wont start i tried messing around with some of the other setting to see if I could find anything wrong but to no solution it will crank but its only cranking around 150-200 rpm.

I'm getting fuel i even tried using some starter fluid to see if that was my issue but nothing . i'm pretty sure that my timing is off but i'm not certain if anyone would be kind enough to supply me with a map for the injectors i have or if anyone wouldn't mind looking at my map to see if they can find something wrong with it i would eternally grateful.

Edited by Johnsontke
updated info
Johnsontke Rookie

Johnsontke

Posted
  • Author
Posted (edited)

Ya i loaded a base map and changed the injector size i also looked around and people were saying to do some math like stock injectors divided by new size and reduce the fuel table by the difference. which map sensor would be the correct one?

Edited by Johnsontke
Johnsontke Rookie

Johnsontke

Posted
  • Author
Posted

Ok sorry for responding so late i just checked it and its dropping to around 8v then itll jump up to 10v and it actually revs a good amount it sounded like it wanted to start but it wouldnt and then i got the smell of gas pretty hard. So i checked the cylinders but they arent flooded so im gonna stick the battery on a charger tonight and try again tomorrow any other suggestions?

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

PM me your exact mods, and what is connected to what input and how everything is wired up e.g. AN1 goes to IAT, etc.

I'll send you a tune file tonight when I'm at home on my tuning laptop. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The king 2.0
      Nissan fuga 450gt android screen

      By The king 2.0 · Posted

      Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • MBS206
      NC MX5

      By MBS206 · Posted

      My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • dbm7
      Automatic Power Button Light Flashing

      By dbm7 · Posted

      Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Duncan
      R34 Plug Identification

      By Duncan · Posted

      Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...