Jump to content
SAU Community

Recommended Posts

Self leveling light problem

Hi guys, 

I've tried to find something on the form but unfortunately I wasn't able to find someone with my problem.

Long story short, I'm not using a lot my car ,so most of the time is parked in the garage. Last time everything was working fine, few days ago I went for a ride and I noticed something wrong with the headlight. When I turned them on instead to leveling at the right position they went all the way down.

Actually I know there's somewhere in the back some sensor can automatically level the headlight, but unfortunately I have no idea where is and if the problem is relative to it.

Any help would be great.

Cheers

PS. The car is a CPV35 2006

PS2 sorry for my bad English.

 

Edited by Loris_V35
Link to comment
https://www.sau.com.au/forums/topic/470369-self-leveling-headlight-problem/
Share on other sites

Does it have a headlight height switch? If not, then check these
http://jp-carparts.com/nissan/partlist.php?maker=nissan&type=152&cartype=13&fig=253&page=15

https://partsouq.com/en/catalog/genuine/unit?c=Nissan&ssd=%24HQARW1d0BAsGAwIVOjlKShl3bWlsbD8OMBM%24&vid=19574&cid=4&uid=558440&q=

Strange that both drop, possible the height controller box died. You should be able to disconnect the motors on the headlights if so.

3 hours ago, niZmO_Man said:

Does it have a headlight height switch? If not, then check these
http://jp-carparts.com/nissan/partlist.php?maker=nissan&type=152&cartype=13&fig=253&page=15

https://partsouq.com/en/catalog/genuine/unit?c=Nissan&ssd=%24HQARW1d0BAsGAwIVOjlKShl3bWlsbD8OMBM%24&vid=19574&cid=4&uid=558440&q=

Strange that both drop, possible the height controller box died. You should be able to disconnect the motors on the headlights if so.

Thanks mate, I think I have found the part.5911885d5b5fc_IMG_20170509_1755341.thumb.jpg.72d54eec8d1f6426616cc00303748514.jpg

I tried to disconnect it and move it manually, but the headlights weren't moving.

591187a438eb1_IMG_20170509_1756041.thumb.jpg.9c858b15e4d86738bbb8e19350aea434.jpg

I tried to disconnect the plug with the lights off, and when I turned the lights on, the motors didn't turn on and didn't lower the lights.  When I put the plug, back in, the motors lowered the lights down.

What do you think? Thanks for any suggestions or advice!

I'd need to get a look at a schematic to understand what's going on but I'd imagine there's a sensor, control circuit and a stepper motor. One of those three components will have failed. If it's an optical sensor, it might just need a clean with isopropyl alcohol. If it's a mechanical sensor, it'll either need a clean or replacement. If it's the control circuit, easiest approach would be to replace it but if it's just a dried out or shorted capacitor, that can probably be cheaply sorted out. If it's the stepper motor, you can determine that by feeding the appropriate pins with 12V to see if you get any movement out of it.

Again, without a schematic, hard to be sure where to begin with the diagnosis past the obvious mechanical bits.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pressure when IDLING, is meant to be 51PSi... So that amperage value needs to go up a fair chunk... I'd personally be factoring for more like 12amp at least on those runs, and at that point you need to hope the already there wiring doesn't drop you a volt or two, as that's a lot of fuel pressure flow drop off from 13.5 to 12V! Taking idle pressure of 51psi, means the pump will be drawing a MINIMUM of 9amps all the time based on your reading of the graph (3bar base, then allowing an extra 0.5bar for boost = roughly 51psi)
    • Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
×
×
  • Create New...