Jump to content
SAU Community

R33 rb30/25 hardline from head to block

thebe

By thebe,
in Engines & Forced Induction

 Share

Recommended Posts

thebe Enthusiast

thebe

Posted
Posted

Hey all

 

Finishing up my rb30/25det build and realized my rb30 doesnt have a thread for this hard line from the head. The engine is in with pretty much every other line and stuff bolted to it (pic from google) so wouldnt really care to take it out and strip apart to tap a hole... Added a pic of my block when it was on a stand, feeling quite stupid :D What is this line for and is it absolutely needed?

 

Thanks alle872bf370d76aab69ef79be3014fe322.jpg9ac3b32c23edf50c521a3b40bc6c6d0f.jpg

thebe Enthusiast

thebe

Posted
  • Author
Posted

After thinking about it for a few moments I think these are my options:

 

1. Tee the head drain to the turbo oil return. Worried if the factory sized drain would be enough for my hx40 AND the head return though...

 

2. Drill and tap a thread to the block. How to prevent metal pieces from getting inside the engine though?

 

3. Take the sump out and drill and weld a fitting for the drain.

 

I was hoping to start my car next weekend for the first time in 2,5 years but dont really want to take shortcuts now that will haunt me in the future. Which would you recommend doing, keeping in mind the engine is in the car? I'm kinda leaning towards 3. If I take the exhaust off and lift the engine as much as I can without disconnecting the gearbox can I get the sump (rb25 oem sized sump) out and back in? That way I could clean the sump and no metal bits would get inside the engine.

 

When I do get the Engine running I will run it on idle to normal temp and then do my first oil change if that changes anything.

 

Other ideas? Thanks

 

 

iruvyouskyrine Grand Master

iruvyouskyrine

Posted
Posted

Is the HX40 ball bearing? Do you have an oil restrictor in the turbo oil feed line?

If both answers are yes then just tee it in to the turbo drain line. And the easiest way to take the sump off is to lower the crossmember while keeping the engine in place so you have access to all the bolts.

thebe Enthusiast

thebe

Posted
  • Author
Posted
Is the HX40 ball bearing? Do you have an oil restrictor in the turbo oil feed line?

If both answers are yes then just tee it in to the turbo drain line. And the easiest way to take the sump off is to lower the crossmember while keeping the engine in place so you have access to all the bolts.

Nope its journal bearing with an3 feed line without a restrictor. The return just meets the turbos demands.

Thanks for the tip with the sump. Its starting to sound like the best option
  • 1 month later...
czy18e Community Regular

czy18e

Posted
Posted

I am also in this boat. I notice rb26's don't seem to have this drain and others have blocked it off. Is it really required with a sump breather?
I am also worried if I plumb it into my turbo drain it will restrict the flow too much. I have a precision 6870.

Ben C34 Grand Master

Ben C34

Posted
Posted
2 minutes ago, czy18e said:

I am also in this boat. I notice rb26's don't seem to have this drain and others have blocked it off. Is it really required with a sump breather?
I am also worried if I plumb it into my turbo drain it will restrict the flow too much. I have a precision 6870.

Rb26 don't need it as it is a drain for the vct.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...