Jump to content
SAU Community

Recommended Posts

But remember the more you raise the rail pressure and ram more fuel throught the injector you change the spray pattern

And you have to leave some headroom in the fuel pump for boost. :headspin:

Around 45psi rail pressure.  its a trade off.  aftermarket inj. cost tons, raising the rail pressure costs F A.  If u had the coin to need 65psi rail pressure u would change the inj anyway.

And since most fuel pumps are rated at 73.5 psi, you would only have 8 psi left for boost. That's not much :wassup:

How long will your fuel pump last if you fit a FPR - ie compared to if you didn't fit a FPR ??

A) The same as if you didn't fit the FPR ?

B) Less because you are labouring the Fuel Pump ??

c) More because of some unknown reason ??

I suspect (B)

And since most fuel pumps are rated at 73.5 psi, you would only have 8 psi left for boost.  That's not much :wassup:

To get that sort of power I assumed you would already be on boost. Surely an aftermarket rising rate regulator will allow you to maintain a slightly elevated fuel rail pressure and then rise it to 65psi by the time you are on full boost.

I don’t have a problem with using a RRR, but if you are pushing that type of power (and I am assuming you have replaced the turbo, fuel pump, computer, intercooler) then surely the cost of injectors is worthwhile even if it’s just insurance for your motor.

How come I get 92-94% injector duty quite regularly with 0.85 bar and standard turbo?

 

One day it hit 100% when i wasn't looking but it seems to have these microsecond spikes like 65% when you've barely touched it.

Car is running rich?

To get that sort of power I assumed you would already be on boost. Surely an aftermarket rising rate regulator will allow you to maintain a slightly elevated fuel rail pressure and then rise it to 65psi by the time you are on full boost.

Yep, that means full boost is 8.5 psi. :rolleyes:

Car is running rich?
You should see my fuel bills! Jeez man. Weird thing is, at the track the exhaust goes brown like it's running lean.

I'm thinking of putting a 2nd hand SAFC in there till I can afford an emanage and a good tune. The ECU I have makes it run so smooth but I think it's just putting way too much fuel in.

Magic1s GTS has 435rwhp on stock injectors and uprated pump,this is the most we have seen sofar on stockers and we have never had any problems at high fuel pressures.

We will fit a bigger pump and see how we go.

This power is in shootout mode.

I see around 80% duty cycle from my 550cc injectors with no FPR and Bosch 044 pump with around 312kw@wheels.

I see around 80% duty cycle from my 550cc injectors with no FPR and Bosch 044 pump with around 312kw@wheels.

That's about right, I have seen around 565 to 570 cc's out of injectors rated at 550 cc's.

So 570 X 80% / 1.34 - 60 = ~300 rwkw

Your 312 rwkw is a pretty good effort. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...