Jump to content
SAU Community

Recommended Posts

Has anyone successfuly used silicone blanking caps before or know of something better to use?

Deleted the IACV from underneath the RB26 inlet plenum so have some decent size (10mm OD?) air ports that need blanking. Ideally i would have crimped them shut and then run a bead of weld across them to keep them 100% sealed but the manifold is already on now so looking for an easier solution. Thinking basically a silicone blanking cap with a little sealant inside and then either a worm drive hose clamp or a spring hose clamp. Will be running up to 30psi so they will have a fair bit of pressure to be holding back.

 

Thanks for your help

Link to comment
https://www.sau.com.au/forums/topic/473026-silicone-blanking-caps/
Share on other sites

I've used both silicone and rubber blanking caps without issue (although not at that boost, but I don't think it makes a difference). For that matter I've used all sorts of "whatever I have around in the right size" sealers like 6mm bolts or solid rod to blank off unneeded hoses. I even saw a mechanic using a old oil filter to seal a gtr intake when doing a leak down test. Basically anything the right size that won't crush under a hose clamp

A blanking cap is no more likely to come loose than any hose joint, so whatever hose clamps you use elsewhere will work the same for a blanking cap.

4 hours ago, iruvyouskyrine said:

For simpleicity reasons, RB26 IACV is a f**king mess and more trouble than it's worth i reckon.

Yeah thinking i might just use hose and then an appropriately sized bolt.

What are you doing for idle control?

And are you talking about the iacv or aac valve for both? I'm converting to single throttle body by removing throttle plates and adding vh45 throttle body.

 Not sure if I need aac/ iacv as the car is auto

Edited by Griffin
Yes

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...