Jump to content
SAU Community

Recommended Posts

Sorry mods, Please feel free to move if needed mods, this relates to Victoria

Have to report my pride and joy stolen today, from Dingley Village, Victoria. Never thought it would happen to me.

 

They broken into the house through a window, ransacked the place, got hold of every key we had, and i believe they towed it away as it had no battery in it. All in plain view of a main road, in broad daylight. between 9am and 2pm on 27/3/18

Doubt i'll ever see her again, but hey. Got to try. Images attached. 

 

 

UPDATE: according to some CCTV footage from down the road, the car was in fact driven away. They had time to install a battery and start it up. In plain view on a main road Jesus.

IMG_0144.JPG

IMG_0151.JPG

Link to comment
https://www.sau.com.au/forums/topic/473648-r34-stolen-dingley-vic/
Share on other sites

I was in Dingley and unfortunately my 34 was not stolen :(

Get insurance people, but breaking into a house to steal shit is another level of nightmare.
Cars are cars, but people who break into other people's houses absolutely should get shafted hard by the law.

Yeah. May as well give a half hearted update.

My efforts of 8 years was found dumped and banged up in Pakenham. People are telling me i should feel lucky they didn't torch it.

They've done significant damage, and plenty of stuff is missing. Wheels, spoiler, bodykit. I also don't know how well the Engine, Gearbox and Handbrake can hold up to two days of absoute torture. They were seen pulling handbrakies at 60km/h . 

I'm insured with LSV - They're alright but I'm not sure this is going to go very well. They've easily done more potential damage than will be covered, but i Dont want to give up on her just yet. Its a stock, tough little motor, with reconditioned gearbox and upgraded clutch. Maybe they survived.

Car will be assessed sometime this week and i'll know.

It doesn't make the slightest bit of difference - but the police know who did it. I know the name of one of them, suprise, he has been in jail before and will most likely be going back.

However there is no recourse to get any compensation back out of them. Just a slow painful process of trying to rebuild what we had.

They didn't just take the car. They took every set of keys in the house. For other cars, safes, etc. Also took my passed grandfathers watch, mobile phones, cameras, mp3 players and a shit tonne of jewlery. None of that will be recovered.

For a short period of time it feels like life is over. The lesson to pass on is have renters insurance, an alarm and cameras where you live ( hard if you're in a rental like me ) and hide your f**king keys.

Do not count on neighbors. this took 45 minutes to accomplish watching the camera footage. no less than 15 people walked directly past the crooks in the act and didn't notice something was up. My own neighbors who know my face, didn't notice 2x strangers struggling with my car. She drove past them twice.

Rely on yourself. Hide your keys. Get kill switches. Get an alarm. Understand that Melbourne is f**ked.

  • Sad 2

It's bittersweet finding it not torched. Nothing really consoling about finding your molested pride and joy.

You couldn't be more right regarding insurance and putting faith only in your self. Run with the mentality that if they really want it and have enough time, they will get it. Everything else you do is just a time delay for them. Therefore insurance is a must. I'm bitterly prepared for the day my car finally gets taken and I'm up to four attempts at theft of it. It's unfortunately part of owning one of these vehicles and the insurance companies know it hence ridiculous premiums on them.

Not meaning to do that thing where everyone brings up their own story of woe, but my motorbike got pinched from my communal apartment carpark in the middle of the day where half the neighbors were home and know my face. They didn't hear the ear piercing disc brake lock, or stop to ask questions, or even tell me if they heard or saw anything. Thieves take advantage of this 100%. So yeah, unfortunately you learned those lessons the hard way.

But chin up. They are just tangible possessions and their disappearance or damage won't erase the memories you have of the good times and the things that matter most to you.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...