Jump to content
SAU Community

Recommended Posts

You’re right, the turbo did sound whistley  on the drive up to the mapper and doesn’t sound half as bad now.

The turbo did over come the leak but at the cost of working harder. Surely it would have build boost differently to if the gasket wasn’t leaking? That’s the best thing about analogue gauges as you can observe fluctuations and trends, digital doesn’t really let you see that unless you are logging...

  • 1 month later...

So I got a pal of mine who’s mapped a few Emanage ultimates to plug his lap top into the Emanage to see if there was anything untoward or just to look at the map (it’s just numbers to me) .

I was a bit out off at the shock he was in as he said that it was retarded across the entire rev range, also, the afm was selected as a standard afm and not as a z32 one which I have, the injectors were also standard when they should have been selected as 440cc.

We took it out with his wide band stuffed up the exhaust ?

He said it was really rich, we got back to mine and he tested the lambda sensor, it was “flatlined” so that needs replacing. 

The only thing that I can confirm is that the brown plug behind the drivers headlight does not lock the timing at 15 degrees when it’s unplugged but does lock the auto box in third as I asked him to measure it. So that is good for mapping on the dyno I guess.

So, I’m going to get a new sensor and ask him to have a crack at mapping it. Or at least ask him to take another look.

Will report back... ?

 

Just for reference its this brown plug ?

A5A3C3C0-9124-4BE2-ADAE-2DB78B5921CD.png

  • 1 month later...

Quick update..

So the car go’s to a show this weekend and I know driving without a decent map could be engine suicide but I’ve had the fuel curve looked at and have been assured that’s it’s safe and there’s so much timing pulled out of it that it won’t det so I’ll trundle down to the show.

Took it out this saterday just gone to make sure everything is just so and ended up forgetting that it shouldn’t be thrashed until it’s been looked at properly and gave it the full biscuit... to my surprise it took off like hell in the night, it felt like it did previously, like before I lost the 58hp the only thing I’ve done recently is stop the re circ from the cam covers to the intake and blank off the lines from the plenum to carbon canister (now gone). I’m not complaining but I’d like to know what the hell is going on still, maybe the maf needs a clean? It is third hand so I may try that.... I’m getting it totally looked at early next month, the entire shooting match mechanically and ECU side by somebody that is very familiar with the emu and can spanner as well....

Will report back...

Edited by paulzy123
Spelling
  • 1 month later...

Hi,

The problem is fixed, I took it to a mate of mine that mapped his own car on the Emanage ultimate. He spent a good long time looking at the wiring. The injector earth wire had a dry joint in the pin in the loom connector and eventually snapped when we went to road map it so that got a new soldered lug. The lambda sensor was goosed so that got replaced. The SAFC 2 I was using to monitor knock still had a map on it and was wired in series with the Emanage wiring which was causing issues so the AFM side of it got removed, the AFM (z32) was spiking at 3.8 volts then dropping to 2.8volts straight after which was also causing problems so he “clamped the voltage?” Apparently it’s not to be used as a permanent fix it’s till I buy another AFM. We spent a couple of hours driving around and doing pulls while he sat on an ancient laptop typing and clicking away saying, “try that” and “do that again” until he turned to me and said right let’s turn the boost up. 

At 18 psi it felt immense and it really was quick enough but he said I could go more so I did but in the end I settled at 19psi as upping it more didn’t seem to feel any quicker. All in all I was on the road around four hours and in his garage at least a day ?

Its quite quick now, well for an auto.

Well, that concludes my thread, thanks for all your advice and help ?

Cheers

Paul

  • Like 4

All's well that ends well. One lesson to be learned is that its very hard to guarantee  a good tune. The tuner might be over -rated, or a shop with a good reputation may hand the job to an employee who is not up to par (although one would like to think that such a person would have their work checked). One thing is for sure a good tune takes time and money!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...