Jump to content
SAU Community

Recommended Posts

First post in here but I've read quite a few. Had 2 Skylines, 4 x C34 Stageas and just current M35 last 2 years. Missus still has a C34.

This one, VQ25DET, started missing about a year ago and a new set of plugs fixed it, completely.

Recently it has started missing when I get right up it - like passing with my foot down when the revs get over 5 grand.

That made me think about the fuel filter, if it was restricting flow when everything is sucking full thirsty.

Did another run that I do, bout 900 km round trip, and just a few km from home it suddenly started missing like a bastard on idle. Then it started missing under throttle and was ugly but didn't get any worse. I nursed it home in 3rd, spinning her over with light throttle to minimise the uneven-ness. Anyway, situation now is, it starts and runs fine - from cold - for about as long as it takes warm up the exhaust.

In about as long as it takes for the exhaust to cool off, it will start and run even again, but for less time.

Ran it for about 10 minutes as I parked it up on a ramp to get under it. After running longer, it would start and miss straight away 20 minutes later. Put my hand up its skirt - turbo was still nice and warm.

So it seems heat related and I don't know if it could be the oxygen sensor, a coil breaking down from running with huge plug gaps, the fuel filter - mmmm nahhh. Gave the air mass sensor a few whacks - that didn't fix it.

Any ideas or "try this to see if"s ?

  • 2 weeks later...

I've got a code reader thing you plug in under the dash - there are no fault codes.

I'm thinking it's the oxygen sensor because it plays up after getting warm. Could be the MAF too I guess.

It's the MAF. Here's some info that might be handy.

While searching for info I read about a guy who had a MAF problem where the engine would run reasonably well without the MAF plugged in but ran like shit when he did plug it in.

The guy advising him said that although the engine will die if you unplug it when it's running, the system defaults to an "acceptable" mixture setting when started without the MAF plugged in. The purpose being to make it driveable to get home or to repair.

So I unplugged my MAF, started it and the engine idled smoothly on all pots.

Plugged it back in, started it and it ran like it had a rag in the intake again.

I know not all MAF faults affect the idle but it's a simple and sure fire test to see if it is the MAF when a rough idle is part of the symptoms.

  • 2 weeks later...

Well it wasn't the MAF sensor - put in a new one. And it isn't the oxygen sensor - got a new one from Kudos and put it in.

If I unplug the MAF sensor and start it, it runs on all pots but is in limp mode - limited to 2K revs.

Plug the MAF in and it misses.

Any ideas?

Checked continuity from mouth of plug back about 20cm on each wire individually, no loss of contact on any of the wires while flexing the wires around where they are bent into the plug.

I'm looking at the ECU unless I can find a big air leak has suddenly opened up somewhere.

My Mrs sez I'm plenty clumsy. I better check them. Where are they?

Eta. Found it. Nothing going on there. Will try replacing it.

Edited by TurboHicas
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah that is not actually a lot. Just painting my GTR frontend and the little bits to make sideskirts/nismo flare pieces work correctly/fit on the sedan/mount up correctly came to about $7000. Is it a lot? Sure. None of this is economical. Economy would be shelling the car and buying a 2010 Corolla to commute in. The perspective of all of this is different.
    • I have the re003s’ on my 06 XT Forester Turbo and I highly rate them for street wet and dry
    • I don't see any issues here. I've been saying all along this is a big job, the price reflects that.  When the car comes back perfect I'm sure it will feel like money well spent. 
    • Remember, take original quote. Double it. Then add a bit more. It's how any project goes.
    • So, I started this repair and got as far as "fixing" the holes with some fibreglass. God all those years working on boats came back quickly. I decided I'd reach out to some rust guys just to see what they would say about it. I came across a guy about 40 mins away and went to see him. He said the windscreen needs to come out, that there might be some more bits around the windscreen and he'd quote them at the time. But his quote was $300 to remove and replace windscreen and $3k for the damage he can see. He said he could respray the roof for $1200 and the bonnet for another $800 (somebody has previously rattle canned it, its horrendous). This is $5300 + any small additional bits. It's a lot, I get that and the name of one of my fave youtube channels 'Not Economically Viable' comes to mind.  I'm not being financially rational, but I've taken him up on the quote. He's opening a new shop in November with more room, so we're waiting for that. I'll leave the currently missing headliner out until then. I'm looking forward to it being fixed and having the paint looking nice again (lots of clear coat issues on the roof too). / flame suit on.
×
×
  • Create New...