Jump to content
SAU Community

Recommended Posts

Hi Guys,

Doing a bit of a garage clean out and have a few things for sale.

Will probably add stuff as i go along and find more, but here is what i have at the moment:

 

Bosch Motorsport top feed 1000cc injectors. Used only for 5000kms with 98  $500

R32 GTR OEM BOV return pipe (used)  $150

R32 GTR OEM front sway bar (used)  $100

R32 GTR OEM aircon ducting (used). Every bit of plastic ducting from under the carpet and dash, except the one that goes to the drivers side vent  $50

R32 GTR OEM Twin Turbo pipe (used)  $100

R32 GTR OEM coil packs (used) $50

Ruzic II 4WD controller (used) $500

R32 carbon boot lid with carbon N1 lip and genuine R35 GTR badge. Boot lid has crazing all through the clear/resin, N1 lip is perfect, so is the badge. $500

R32 GTR series 2 textured center console surround in mint condition with lighter (used) $500

R32 GTR series 2 textured center console surround with a crack at the very bottom next to gear boot, and one broken tab at the very top $100

Sparco Sprint V fixed back seats. Pair, no rails. Very little use, some marks from storage but no tears. $500

 

Open to offers within reason.

Items are located just south of Wollongong.

Willing to post smaller items at buyers expense, larger items like ducting, seats and boot lid prefer pick up.

There will be more to come as I get through everything.

I will upload pics when I get a chance.

Link to comment
https://www.sau.com.au/forums/topic/476257-gtr-bits-and-pieces/
Share on other sites

Also have:

Haltech I/O 12 Channel Box A only, no lead (used) $300

Haltech Can Hub Mini with 2 cables (used) $100

Haltech O2 sensor with new weld on bung, still in good condition (used) $100

R32 GTR OEM map sensor (used) $50

R32 GTR OEM Alternator (used) $100

R32 GTR OES CAS Bracket (used) $50

7 hours ago, horus83 said:

Hi Mate, 

Do you still have the 

Center console surround, Can you send me a pic?

 

I still have both. Which one were you after, the mint or cracked one?

16 hours ago, horus83 said:

If you can PM both ill decide which one? I am assuming it is the grey texture finish ones?

Yes they are both the series 2 grey textured finish ones. PM sent.

Some pics.

Ducting, Sway bar, oem map sensor, Haltech O2 sensor, Haltech I/O Expander Box A, oem cas bracket, Haltech Can Hub Mini, Injectors, Ruzic II 4WD Controller, Mint series 2 textured stereo/shifter surround.

More to come.

20130707_150149.jpg

20130707_151959.jpg

53570985_403763456835583_3278011081456353280_n.jpg

53846715_261526194778397_4076207762458017792_n.jpg

53889046_326232208251509_7104461655223828480_n.jpg

54190702_318975015486010_4799588565589688320_n.jpg

54255016_2110808939001413_7434246209331527680_n.jpg

54428409_2537318289616251_8989685026647965696_n.jpg

54433166_2313535578686282_6420320025495732224_n.jpg

55564269_270211360579297_7215893151494438912_n.jpg

console 1.jpg

console 2.jpg

console 3.jpg

console 4.jpg

console 5.jpg

  • 3 weeks later...
  • 1 month later...
1 minute ago, theskidmasta said:

i know you prefer pick up,  but if you can calculate shipping to socal usa i can take the boot lid off of your hands

With the size of this thing shipping it to the states would not be worth while.

You would be better off sourcing one locally.

1 minute ago, theskidmasta said:

i cant find a decent one in the US for less than 1k AUD

 

Well JACKA87 is supposed to be picking it up this friday.

If he doesn't pick it up, I'll look into the shipping costs, but i know it wont be cheap and the total cost will be up around that 1k figure im pretty sure.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...