Jump to content
SAU Community

Recommended Posts

1999 Nissan Stagea

(rb25det non neo)

is an RS so is factory RWD. has been manual swapped using an R34 GTT box

Need help before I take to mechanic as could be a simple fix. When driving normally there isn't a noticeable misfire. But when on boost, especially as soon as boost starts to just past half max psi the car stutters coz the misfire but continues up the rev range. Usually it's once or twice when I floor it but sometimes it will misfire alot when on boost. Cold or warm it happens with both. The more I drive it the worse it's getting and have no clue what it may be apart from maybe sparkplugs but it's fine til it hits boost. Also on idle it runs a little rough. Anyone know any possible solutions or possibly what may cause this and what to check. Cheers 

-Any help is appreciated 

mods include:

gt2860rs turbo

Bosch 750cc injectors

Z32 afm

Sard Fuel Pressure regulator

3 port boost solenoid

HKS Bov

Walbro 255 fuel pump

Front mount intercooler

ali rad

pod filter

nistune ecu. 

Recently had new intercooler piping, new coil packs, new fuel pump and new turbo core

Tuned at hyperdrive making 277rwhp at 14psi

Link to comment
https://www.sau.com.au/forums/topic/476537-help-stagea-missfire/
Share on other sites

Turn up the boost!

Would have thought you replaced the plugs when you did the coils. What sort of coils are they? Many dodgy ones out there.

Plugs NGK BCPR7ES (copper) or better PFR7G-11S

Try a smaller gap 0.8mm

19 minutes ago, Nick666646 said:

I'll do that tonight and I'll let you know the results. But may I ask what does the gap difference do to help? I'm far from being a mechanic aha 

Much like it is easier to throw a ball across a smaller lake, it is easier for spark to jump a smaller gap.  

Or it’s easier to shoot a ball of lightning from your finger  a smaller distance than a larger distance. 

  • 1 month later...

Sorry guys had a lot of work and never got around to doing so. Took out and clean sparkplugs. Gapped to 0.6 but problem still consists. (Car idles a bit better but still original problem is there) But found something weird. When driving if I give it hurts and bang off limiter a little bit the misfire seems to go away for 5-10 mins and then it's back? Really confused

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That looks good, but I think you're going to need much beefier side skirts now.
    • They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • Define "starting to fail". Wy not just rebuild them?
    • Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...