Jump to content
SAU Community

Ignition coils stuck in spark plug tubes

Blakeo
 Share

Recommended Posts

Blakeo Rising Star

Blakeo

Posted
Posted

This sounds extremely dumb, but it's true and I'm not sure what to do about it. 

My 2005 v35 skyline was misfiring, found out to be oil in the spark plug holes getting into ignition coils. 

I didn't have the $800 for the genuine valve covers at the time and I read a temporary solution was to use rtv and seal the coilpacks in the spark plug tubes. I don't know if that was a troll but it worked for about 3 months, now it's back misfiring and the one coil I could get out had oil in it. The others I've tried to pull out but the boot is stuck inside the spark plug tube because of the silicon ?

Has anyone ran into this before and any suggestions how I can get it out without damaging the coil boot?

Ben C34 Grand Master

Ben C34

Posted
Posted
31 minutes ago, Blakeo said:

Alright guys, if anyone else has this issue in the future. I bought some CRC Gasket Stripper. Sprayed it down the sides of the spark plug tube let it soak for a minute or two and I could pull the boot straight out. 

Good work, very lucky

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Predator1
      Tomei gasket

      By Predator1 · Posted

      Didnt realise RB's had more then 1 head.
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • Kinkstaah
      Unpeeling the Orange

      By Kinkstaah · Posted

      The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...