Jump to content
SAU Community

Recommended Posts

Hi everyone, I have purchased a R32 GTR that was unregistered. the previous owner said it was registered in NSW 6-7 years ago. Did a PPSR check and it came clean, the date of compliance was more than 30 years ago, last registered state was NSW & currently unregistered.. I could only find the VIN number inside the bonnet, which match the chassis & engine number, couldn't find the Compliance plate anywhere but the PPSR check says its compliant. I was told by my mates that I need to get an ID check done to get it registered in SA. any help is highly appreciated. 

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/481251-r32-gtr-missing-compliance-plate/
Share on other sites

Definitely need id check. They aren't the same guys that do the full inspections, but they won't let obvious modifications through, can't have loud exhaust etc.

Ring them and ask re missing plate. Is it an import?

1 minute ago, Ben C34 said:

Definitely need id check. They aren't the same guys that do the full inspections, but they won't let obvious modifications through, can't have loud exhaust etc.

Ring them and ask re missing plate. Is it an import?

Okie. it got coilovers, turbo gauge & got few chassis rail bend due to forklift..exhaust it not loud, apart from that its all good. 

I was told it was on storage for few years here in aus. probably grey import 30 years back, maybe has taken part in 1990 bathurst :D lol..

ring who ? it was previously registered in NSW though.

Ring the place that does the inspections.

 

Metropolitan Adelaide

Metropolitan vehicle identity assessment station
7 Naweena Road
Regency Park SA 5010

Phone 8400 8777

Open 8.00 am to 4.30 pm Monday to Friday. No appointment needed.

 

 

Doesn't mater where it was previously registered. These are the guys that will make or break your day.  It has to go through there.

Coilovers won't work with them, but you may as well ask yourself.

 

17 minutes ago, Ben C34 said:

Ring the place that does the inspections.

 

Metropolitan Adelaide

Metropolitan vehicle identity assessment station
7 Naweena Road
Regency Park SA 5010

Phone 8400 8777

Open 8.00 am to 4.30 pm Monday to Friday. No appointment needed.

 

 

Doesn't mater where it was previously registered. These are the guys that will make or break your day.  It has to go through there.

Coilovers won't work with them, but you may as well ask yourself.

 

Will give them a call. Thanks Mate!.. 

The mechanic said Its cheaper for me to get the coilovers adjusted to legal limit and get an engineer certified. Rather than changing it to stock. I don't mind both. 

  • Like 1

if it gets called in for an actual roadworthy inspection after the ID check (which I would expect!), then;

Horn, demisters (front and rear), all lights everywhere - must be working.

Seatbelts must not be frayed.

ECU must be stock.

Numberplates must not me bent, cut or otherwise modified (and this probably won't be an issue on an unreg car!)

Seat foam must not be collapsing and dandruffing the floor.\

>100mm ground clearance everywhere.

Must be above minimum eyebrow height at all 4 corners.

Brake performance will be tested on their brake tester rig.

Steering mods (ie HICAS lock bar) will be looked at. And failed, if present.

Probably more.

 

14 hours ago, GTSBoy said:

if it gets called in for an actual roadworthy inspection after the ID check (which I would expect!), then;

Horn, demisters (front and rear), all lights everywhere - must be working.

Seatbelts must not be frayed.

ECU must be stock.

Numberplates must not me bent, cut or otherwise modified (and this probably won't be an issue on an unreg car!)

Seat foam must not be collapsing and dandruffing the floor.\

>100mm ground clearance everywhere.

Must be above minimum eyebrow height at all 4 corners.

Brake performance will be tested on their brake tester rig.

Steering mods (ie HICAS lock bar) will be looked at. And failed, if present.

Probably more.

 

U reckon ? 

I will get it close to stock as much as possible. don't want to get defected later on for something minor, being these cars are cop magnets..lol

14 hours ago, Butters said:

1988 cars and some very early 1989 brought in under 15 year old rule before axed did not get compliance plates. Only vin. 

What year is it ?

Yaaa.. thats what I have gathers so far... this is a 1989 car & compliance in PPSR shows 1989 was the year of compliance. 

Been there, done that, as I said elsewhere/before. Engine conversion required full inspection. The blokes who do it are not silly, and they know the tricks, and they know the rules, and they will only be a little bit flexible on some of them.

I've seen dipshits go back 3 times.

  • Like 2
30 minutes ago, GTSBoy said:

Been there, done that, as I said elsewhere/before. Engine conversion required full inspection. The blokes who do it are not silly, and they know the tricks, and they know the rules, and they will only be a little bit flexible on some of them.

I've seen dipshits go back 3 times.

Engine & most stuffs are stock & matches the PPSR :) .. only the Coilover is aftermarket.. 

33 minutes ago, Ben C34 said:

Did you ring them?

 

Ya, they were friendly. If I have coilovers I have to get an engineer certificate and get vehicle modification inspection done. I might as well put a stock suspension and get ID Check done. Don't mind leaving the stock in. Any idea where I can get one? 

As the vehicle has been previously registered I may have to get an exemption of compliance or check with the previous state where it was registered and get that info. Not bad 

 

  • Like 1
On 01/10/2020 at 9:22 PM, GTSBoy said:

if it gets called in for an actual roadworthy inspection after the ID check (which I would expect!), then;

Horn, demisters (front and rear), all lights everywhere - must be working.

Seatbelts must not be frayed.

ECU must be stock.

Numberplates must not me bent, cut or otherwise modified (and this probably won't be an issue on an unreg car!)

Seat foam must not be collapsing and dandruffing the floor.\

>100mm ground clearance everywhere.

Must be above minimum eyebrow height at all 4 corners.

Brake performance will be tested on their brake tester rig.

Steering mods (ie HICAS lock bar) will be looked at. And failed, if present.

Probably more.

 

Can confirm. At least here in WA. I just passed the pits on Friday :) 

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...