Jump to content
SAU Community

Recommended Posts

Hey all,

Here it goes again, lol. As some of you might have known from my last post I did lose a tiny bit of coolant every few months, and it's been like that for years (probably since I bought the car) but I noticed last week that I heard water slushing in my dashboard, then noticed I had no heat when I turned it on (but sometimes it would come on), then yesterday out of nowhere the temperature gauge went about half way between operating temperature and the red zone, I noticed before hand that my radiator had no coolant and the hose was cold I'm pretty sure (reservoir was full).

 

Sounds like my heater core, is clogged, but as soon as the aircon produced hot air the temperature went down then back up again because the heating stopped working, so makes me think it's the heater core. But I noticed this morning when I woke up almost all my coolant was gone, went to check the leak underneath and it seemed to be above the thermostat somewhere (didn't seem like the thermostat was leaking or the head gasket but it was above the thermostat area.

The car is a 2001 Impreza (no surprise there of coolant issues, haha) Can a clogged heater core cause me to lose that much coolant? Surely it's not the head gasket, there is no bubbles in reservoir, milkshake or anything like that. I opened up the timing cover a bit to see if there was water and if the timing belt was wet but it was all dry as a bone.

1 minute ago, Ben C34 said:

Not clogged, you have trapped air and need to bleed the system properly. 

 

Find and fix the leak also dude.

From what I understand for coolant I need to put it to the highest point or use the bleeder valve? Will try to find it, was quite difficult to see. I never had bubbles in my cooling system no idea how it developed it.

3 hours ago, GTSBoy said:

Typical Subaru head gasket failure from inside of block out through bottom corner onto road. It's f**ked.

I hope not lol. it was somewhat on the corner, but didn't seem it was near the head gasket. Tomorrow I'm gonna take some coolant out of the resoviour as it's a bit above full and put in the radiator see if I get any bubbles, try to bleed the sytem as ben suggested

4 hours ago, GTSBoy said:

Typical Subaru head gasket failure from inside of block out through bottom corner onto road. It's f**ked.

Its the early symptom of a compression leak to coolant jacket. Your head gasket, probably only one side, has failed. They have shit heater cores which leak under these circumstances, Also Subaru since the early seventies have decided that the heater core is the most important part of the car, they put a heater core on the production line and build the Subaru around it. Good luck.

  • Like 1
1 hour ago, Rusty Nuts said:

Its the early symptom of a compression leak to coolant jacket. Your head gasket, probably only one side, has failed. They have shit heater cores which leak under these circumstances, Also Subaru since the early seventies have decided that the heater core is the most important part of the car, they put a heater core on the production line and build the Subaru around it. Good luck.

Ah fml, I really hope it's not the case haha. I just saw this video , and the leak is pretty much the same area. 

 an

  • Like 1

Just one other thing, its a common mod to bypass some of the heater water (Google it), it takes pressure off the core which can become blocked, I did it to both my daughters Subaru's as a preventative measure.

Just add the double tee with a short piece of 5/8 hose between it, gives faster warm up, ensures flow to the thermostat, and seems to keep them cooler in traffic. The pic below is a Subaru probs not yours, but Subaru mark their hoses. I got the Tee's from Bunnings, cheap as chup's,Bro across the water.

Heater core Inlet/outlet identification | Subaru Outback Forums

Heater Bypass Adaptor

Edited by Rusty Nuts
additional information
On 6/9/2021 at 11:00 AM, Rusty Nuts said:

Just one other thing, its a common mod to bypass some of the heater water (Google it), it takes pressure off the core which can become blocked, I did it to both my daughters Subaru's as a preventative measure.

Just add the double tee with a short piece of 5/8 hose between it, gives faster warm up, ensures flow to the thermostat, and seems to keep them cooler in traffic. The pic below is a Subaru probs not yours, but Subaru mark their hoses. I got the Tee's from Bunnings, cheap as chup's,Bro across the water.

Heater core Inlet/outlet identification | Subaru Outback Forums

Heater Bypass Adaptor

Hey mate thanks for that. I was going to originally unplug my heater core, but then I realized I had no coolant in the radiator and that is probably why I have no heating. I drove it like that for a week and the temperature gauge didn't go up so hoping I didn't cause any damage lol.

  • Haha 1
On 6/9/2021 at 11:00 AM, Rusty Nuts said:

Just one other thing, its a common mod to bypass some of the heater water (Google it), it takes pressure off the core which can become blocked, I did it to both my daughters Subaru's as a preventative measure.

Just add the double tee with a short piece of 5/8 hose between it, gives faster warm up, ensures flow to the thermostat, and seems to keep them cooler in traffic. The pic below is a Subaru probs not yours, but Subaru mark their hoses. I got the Tee's from Bunnings, cheap as chup's,Bro across the water.

Heater core Inlet/outlet identification | Subaru Outback Forums

Heater Bypass Adaptor

I got someone to double check it, looks like the water pump is quited f**ked lol. Leaking all the time, gotta drive it down to a shop 5km away, hopefully don't lose all my coolant on the way.

On 6/9/2021 at 11:00 AM, Rusty Nuts said:

Just one other thing, its a common mod to bypass some of the heater water (Google it), it takes pressure off the core which can become blocked, I did it to both my daughters Subaru's as a preventative measure.

Just add the double tee with a short piece of 5/8 hose between it, gives faster warm up, ensures flow to the thermostat, and seems to keep them cooler in traffic. The pic below is a Subaru probs not yours, but Subaru mark their hoses. I got the Tee's from Bunnings, cheap as chup's,Bro across the water.

Heater core Inlet/outlet identification | Subaru Outback Forums

Heater Bypass Adaptor

I saw the process it seems pretty easy actual to change the belt and all the idlers and even to take off the harmonic balancer though for this damn car finding the workshop manual seems impossible and i found one but it doesn't talk about the torque settings on the pulleys. 

5 hours ago, silviaz said:

saw the process it seems pretty easy actual to change the belt and all the idlers and even to take off the harmonic balancer though for this damn car finding the workshop manual seems impossible and i found one but it doesn't talk about the torque settings on the pulleys. 

This is the factory procedure;

13.Crank Pulley
A: REMOVAL
1) Remove the V-belts. <Ref. to ME(H4SO)-36,
REMOVAL, V-belt.>
2) Remove the crank pulley bolt. To lock the crankshaft,
use Shop Tool 499977100 CRANK PULLEY WRENCH
3) Remove the crank pulley.
 
B: INSTALLATION
1) Install the crank pulley.
2) Install the pulley bolt.
To lock the crankshaft, use Shop Tool 499977100 CRANK PULLEY WRENCH
(1) Clean the crankshaft thread using compressed air.
(2) Apply engine oil to the crank pulley bolt seat and thread.
(3) Tighten the bolts temporarily with tightening torque of 44 N·m  or   33 ft-lb).
(4) Tighten the crank pulley bolts. Tightening torque: 180 N·m   or  132.8 ft-lb)
 
3) Check that the tightening angle of the clamp pulley bolt is a minimum of 65°,  Perform the following procedures when less than 65°.
(1) Replace the crank pulley bolts and clean them. Crank pulley bolt: 12369AA011
(2) Clean the crankshaft thread using compressed air.
(3) Apply engine oil to the crank pulley bolt seat and thread.
(4) Tighten the bolts temporarily with a tightening torque of 44 N·m (4.5 kgf-m, 33 ft-lb).
(5) Tighten the crank pulley bolt an additional 65° to 75°.
 
12 hours ago, Rusty Nuts said:

This is the factory procedure;

13.Crank Pulley
A: REMOVAL
1) Remove the V-belts. <Ref. to ME(H4SO)-36,
REMOVAL, V-belt.>
2) Remove the crank pulley bolt. To lock the crankshaft,
use Shop Tool 499977100 CRANK PULLEY WRENCH
3) Remove the crank pulley.
 
B: INSTALLATION
1) Install the crank pulley.
2) Install the pulley bolt.
To lock the crankshaft, use Shop Tool 499977100 CRANK PULLEY WRENCH
(1) Clean the crankshaft thread using compressed air.
(2) Apply engine oil to the crank pulley bolt seat and thread.
(3) Tighten the bolts temporarily with tightening torque of 44 N·m  or   33 ft-lb).
(4) Tighten the crank pulley bolts. Tightening torque: 180 N·m   or  132.8 ft-lb)
 
3) Check that the tightening angle of the clamp pulley bolt is a minimum of 65°,  Perform the following procedures when less than 65°.
(1) Replace the crank pulley bolts and clean them. Crank pulley bolt: 12369AA011
(2) Clean the crankshaft thread using compressed air.
(3) Apply engine oil to the crank pulley bolt seat and thread.
(4) Tighten the bolts temporarily with a tightening torque of 44 N·m (4.5 kgf-m, 33 ft-lb).
(5) Tighten the crank pulley bolt an additional 65° to 75°.
 

Thanks man. Is that for the 2001 subaru impreza rx 2.0ltr automatic? 

  • Like 1

Its what I have used for Four Cylinder Subaru's for years. Some Guys I worked with just go directly to 150 ft-lb as this definitely gets the angle past 65 degrees. Up to you bud, heaps of luck.

  • Thanks 1
3 hours ago, Rusty Nuts said:

Its what I have used for Four Cylinder Subaru's for years. Some Guys I worked with just go directly to 150 ft-lb as this definitely gets the angle past 65 degrees. Up to you bud, heaps of luck.

Thanks as always. I think I might get a shop to do it, I've got a knack for ruining things I touch, haha. 

On 6/13/2021 at 11:39 AM, Rusty Nuts said:

Its what I have used for Four Cylinder Subaru's for years. Some Guys I worked with just go directly to 150 ft-lb as this definitely gets the angle past 65 degrees. Up to you bud, heaps of luck.

Got my water pump and other stuff changed today i noticed the coolant resoviour was above the max line about an inch now it dropped twice and is an inch below the line. oh boy here we go haha, costed me a pretty penny to. Will keep this thread updated. I just hope that was air bleeding out of the system.

10 hours ago, silviaz said:

Got my water pump and other stuff changed today i noticed the coolant resoviour was above the max line about an inch now it dropped twice and is an inch below the line. oh boy here we go haha, costed me a pretty penny to. Will keep this thread updated. I just hope that was air bleeding out of the system.

You are meant to bleed the air yourself. Not just randomly hope it happens.

2 minutes ago, Ben C34 said:

You are meant to bleed the air yourself. Not just randomly hope it happens.

The mechanic did it or he should have at least i did see he was adding coolant when i arrived to the shop. The leak is gone though. Will keep an eye on it. There are no air bubbles in the radiator cap or resoviour.

Edited by silviaz
  • Like 1
On 6/19/2021 at 11:59 PM, silviaz said:

Got my water pump and other stuff changed today i noticed the coolant resoviour was above the max line about an inch now it dropped twice and is an inch below the line. oh boy here we go haha, costed me a pretty penny to. Will keep this thread updated. I just hope that was air bleeding out of the system.

Thats pretty normal actually. What you have to watch for, Check your coolant reservoir after a run and the car is hot, if the level is high or overflowing, you have a compression leak from HG. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...