Jump to content
SAU Community

R33 Front Fuse Box Terminals

Robospecta
 Share

Recommended Posts

Robospecta Rookie

Robospecta

Posted
Posted

Hi All,

I'm wanting to add some additional wire terminals for blade fuses into the front fuse box on my 1997 R33 GTST as part of cleaning up the previous owners dodgy wiring. The positive side of the terminals are there that connect to the +ve bus, but for some of the fuse slots the negative wire terminal is missing. These wire terminals pin into 24381 on the catalogue diagram below.

image.thumb.png.eecfbfc3a41278b296458f943f98b4c7.png
image.thumb.png.daf01d5e73d35992bf34beff75bb8f40.png

 

Does anyone know what wiring terminals are used in the fusebox? I know a lot of Sumitomo connectors and terminals are used elsewhere on the car.

Alternatively, does anyone know the trick to depin one so I can identify it visually? I haven't had any luck so far. From the catalogue diagram it looks like the whole fusible link holder removes which might give me some more success in getting a better view to depin, but I have been unable to figure out how it comes out yet. I'm sure it's clipped in.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/483002-r33-front-fuse-box-terminals/
Share on other sites
Duncan Grand Master

Duncan

Posted
Posted

I can't confirm the connector to buy separately and I guess you mean load not negative for the side you are trying to add.

Having said that, groups of fuses will unclip from the main holder. You can see the little tabs in your first pic, eg to the left of the left hand 15A fuse - you need to flick all of them out then pull the section out of the frame. If you can't get every clip at the same time (lots of little screwdrivers...) you need to start at one end with a couple of tabs and pull the holder up far enough to get past the clips, then hold it up and move to the next set.

That will get the fuse holder out of the frame, but you may ind it can't come far due to wire lengths at the rear.

From behind, you will see how to depin the fuses

  • Like 1
Robospecta Rookie

Robospecta

Posted
  • Author
Posted

Was able to pull out the terminal and identify. Posting here in case anyone searching in future needs this information.

This is the wiring terminal used for the blade fuses in the front fuse box of my Nissan Skyline R33 GTST.
Yazaki 7126-8771
https://www.nbzte.com/yazaki-connector-7126-8771.html

Thanks all for your help.

  • Like 1
  • Thanks 1
Duncan Grand Master

Duncan

Posted
Posted
On 16/11/2021 at 4:59 PM, Robospecta said:

Was able to pull out the terminal and identify. Posting here in case anyone searching in future needs this information.

This is the wiring terminal used for the blade fuses in the front fuse box of my Nissan Skyline R33 GTST.
Yazaki 7126-8771
https://www.nbzte.com/yazaki-connector-7126-8771.html

Thanks all for your help.

Excellent detective work...how did you identify that terminal?

  • Like 1
Robospecta Rookie

Robospecta

Posted
  • Author
Posted

With about 10 - 20 hours of searching on the internet 😂 Unfortunately no markings or stamps on the terminal that I could see even under magnification.

Eventually I joined an Automotive Connector Identification group on Facebook, and searched for "Nissan" in their posts. Found a post with someone looking to identify a terminal on their 2000 Nissan Maxima. Someone had replied with a photo and part number of the terminal I was after. Didn't happen to be what the original poster was looking for, but I was certainly grateful that someone had commented it. 🙃
https://www.facebook.com/groups/4359499570789592/posts/6049608905111975

  • 4 weeks later...
Robospecta Rookie

Robospecta

Posted
  • Author
Posted

Hi @sonic99 :) 

If you're looking for the part numbers for a "front fuse box cover" perhaps best to start a new thread where we can help you. This thread is concerned with the terminals crimped onto the end of wires in the fuse box.

If you are in fact looking for "front fuse box wire terminals" then if you post a photo I can compare with mine and let you know if the part number above is applicable. I can't see why it would be different.

  • Thanks 1
  • 1 year later...
dee242 Enthusiast

dee242

Posted
Posted
On 11/11/2021 at 12:02 AM, Duncan said:

I can't confirm the connector to buy separately and I guess you mean load not negative for the side you are trying to add.

Having said that, groups of fuses will unclip from the main holder. You can see the little tabs in your first pic, eg to the left of the left hand 15A fuse - you need to flick all of them out then pull the section out of the frame. If you can't get every clip at the same time (lots of little screwdrivers...) you need to start at one end with a couple of tabs and pull the holder up far enough to get past the clips, then hold it up and move to the next set.

That will get the fuse holder out of the frame, but you may ind it can't come far due to wire lengths at the rear.

From behind, you will see how to depin the fuses

I need help getting mine out

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      GTR R34 Limp Mode

      By GTSBoy · Posted

      Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • steven7270
      GTR R34 Limp Mode

      By steven7270 · Posted

      So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Dose Pipe Sutututu
      SAUNSW - Cruise - Albion Park Aviation Museum - 9th August

      By Dose Pipe Sutututu · Posted

      Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • PranK
      Rusty roof repair

      By PranK · Posted

      Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • GTSBoy
      Rusty roof repair

      By GTSBoy · Posted

      That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...