Jump to content
SAU Community

Recommended Posts

On the track (as in a circuit not a 400 straight line) I've seen my fuel temps go above 65 degrees after 10 laps of Wakefield.

Day to day driving around town probably 30s to 40s, mind you I run PWM so both pumps in the surge are duty cycled. The DW200 lift pump however is just on factory wiring with the resistor deleted.

And no your fuel temp isn't that high.

Not high at all. In the NT until I staged my two 400lph AEM external pumps with twin -8 feeds from surge with AEM 340lph in tank pump I was seeing 70 - 75 on the highway, ambients were above 40 though. After staging the 400s the temps came down under 50.

On the other 32 with PWM we had similar reduction in temp as Johnny suggested on a single Walbro 525lph pump.

  • Like 1
On 3/28/2022 at 9:23 AM, Predator1 said:

Thinking of adding the Setrab fan assisted cooler.

I wouldn't bother unless;

  • You're having fuel temp related problems that you didn't mention, or
  • You're going to change the way that you use the car that could/would lead to heat either increasing or being more of an issue, or
  • You like introducing more points of failure.
  • Like 1

I would not stage the pumps and duty cycle them together and ramp them up based on MAP (as the load axis).

At 100hz, the Walbro 450/460s don't like any duty under 40% they start to make an awful hum, however any higher they seem ok!

I suspect your pumps wouldn't be too far off that.

Part of the problem you have is 1x pump is always at full filt _ your lift pump. They're heating up your fuel unnecessarily. 

 

Also, if you have proper injector data and fuel data i.e. fuel temp vs fuel density vs. ethanol then there's no real issue with warm fuel.

This is how I've done mine (note must tuning shops will not do this, as customers don't pay them enough for their time - Link and MoTec have this predefined).

image.thumb.png.1907e8fa6b99748a9fc2f07c6edd00d7.png

On 28/03/2022 at 12:47 PM, Dose Pipe Sutututu said:

I would not stage the pumps and duty cycle them together and ramp them up based on MAP (as the load axis).

At 100hz, the Walbro 450/460s don't like any duty under 40% they start to make an awful hum, however any higher they seem ok!

I suspect your pumps wouldn't be too far off that.

Part of the problem you have is 1x pump is always at full filt _ your lift pump. They're heating up your fuel unnecessarily. 

 

Also, if you have proper injector data and fuel data i.e. fuel temp vs fuel density vs. ethanol then there's no real issue with warm fuel.

This is how I've done mine (note must tuning shops will not do this, as customers don't pay them enough for their time - Link and MoTec have this predefined).

image.thumb.png.1907e8fa6b99748a9fc2f07c6edd00d7.png

I used your fuel density table you sent me and put it in the Elite before Simon tuned it at Morpowa last year, very handy 👍

  • Like 1
On 28/03/2022 at 2:23 PM, BK said:

I used your fuel density table you sent me and put it in the Elite before Simon tuned it at Morpowa last year, very handy 👍

no more silly AFR hunting at idle, regardless of fuel temp or big injectors :) 

Haltech is great, provided it's used properly.

400902463_FPSetup.thumb.PNG.dab39a5be7e6b07d86d35f35dda0a9c0.PNG14233463_FPDuty.thumb.PNG.239b18e14e711d2820d01921307e2cd9.PNG

 

Funny you mentioned the hum noise, cos mine makes that too. I noticed in the logs stats, from memory my max Inj DC is around 38%.. So judging by that, my FP's sitting under 70%?? I think with PWM its the opposite?

What's your PWM setup?

 

On 28/03/2022 at 4:17 PM, Dose Pipe Sutututu said:

I would not stage the pumps and duty cycle them together and ramp them up based on MAP (as the load axis).

At 100hz, the Walbro 450/460s don't like any duty under 40% they start to make an awful hum, however any higher they seem ok!

I suspect your pumps wouldn't be too far off that.

Part of the problem you have is 1x pump is always at full filt _ your lift pump. They're heating up your fuel unnecessarily. 

 

Also, if you have proper injector data and fuel data i.e. fuel temp vs fuel density vs. ethanol then there's no real issue with warm fuel.

This is how I've done mine (note must tuning shops will not do this, as customers don't pay them enough for their time - Link and MoTec have this predefined).

image.thumb.png.1907e8fa6b99748a9fc2f07c6edd00d7.png

 

On 28/03/2022 at 5:30 PM, Dose Pipe Sutututu said:

ooo I lied, I run it at 200hz

image.thumb.png.28d48641d64f99dde2fbb0f277e4f30a.png

 

It's 100AMP Jaycar SSR, with flyback diodes on each Walbro 450L

Ah yeah so mines at 250hz, doubt that be an issue. The tuner didnt stick flybacks on my SSR which I always was a bit dubious about. I run the 100A SSR too. 

On 28/03/2022 at 3:38 PM, Predator1 said:

The tuner didnt stick flybacks on my SSR which I always was a bit dubious about

You need flyback diodes, if not your SSRs would be ripping hot and will fail with time.

On 28/03/2022 at 2:10 PM, Dose Pipe Sutututu said:

Look at us, all so modern :) 

Love it - running all pumps full tilt all the time is stupid!

I'd like to PWM the blue 32 with the twin 400 pumps, but can't be stuffed so it will stay staged. It works perfectly and probably draws less current than PWMing 2 pumps simultaneously. PWM on the primary external and keep the secondary staged if I can be bothered would be the go.

For Predator1 - absolutely use a flyback diode as above. I like the 1N5404 at 400v / 3A for a bit of overkill.

  • Like 1
On 28/03/2022 at 2:26 PM, Predator1 said:

Thanks guys. I'm just concerned about my tune. 

So safe to just stick 1 flyback across the SSR terminals that go towards my pumps? I think both pumps get their positive from the SSR. I'll have to double check.

The best place for a flyback diode is at the load, so across the pump terminals ideally.

.IMG_20210626_115220_0.thumb.jpg.4b9eaa7b756269c3b7d8cf71b3c8eb65.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...