Jump to content
SAU Community

R35 BMC Conversion

Meap
 Share

Recommended Posts

Meap Rookie

Meap

Posted
Posted

Hi everyone,

I wasn't really sure where to post this but I'm trying to retrofit an R35 BMC and booster to my R32 GTR. I know the brake lines on the BM50 are M10x1.0, but I can't for the life of me find any information on the thread size on the BMC of the R35 which I believe is called J069?

I know this is probably a long shot but if someone could bless me with the correct thread size that would be marvelous!

Thanks in advance!

Link to comment
https://www.sau.com.au/forums/topic/483737-r35-bmc-conversion/
Share on other sites
Meap Rookie

Meap

Posted
  • Author
Posted

I'm already in contact with him, but thanks!

Reason I made a new post is because he isn't 100% sure what size the fittings are, and I was wondering if maybe there was someone who does know.

I'll figure it out sooner or later! (Latest when I buy an R35 BMC and realise my current braided lines don't fit haha!)

  • 8 months later...
deongster Mentor

deongster

Posted
Posted
On 09/06/2022 at 8:04 AM, Meap said:

I'm already in contact with him, but thanks!

Reason I made a new post is because he isn't 100% sure what size the fittings are, and I was wondering if maybe there was someone who does know.

I'll figure it out sooner or later! (Latest when I buy an R35 BMC and realise my current braided lines don't fit haha!)

How did you go with this? I also bough AN3 braided male - i think its wrong size... do you have pic of wiring?

  • 1 month later...
Meap Rookie

Meap

Posted
  • Author
Posted
On 2/24/2023 at 12:18 PM, deongster said:

How did you go with this? I also bough AN3 braided male - i think its wrong size... do you have pic of wiring?

Sorry for the late reply, the fitting is actually M12x1.0. Regarding the picture of the wiring, do you mean the wiring for the fluid level sensor? If so, this is just a simple + and - circuit.

  • 2 months later...
deongster Mentor

deongster

Posted
Posted
On 17/04/2023 at 7:29 PM, Meap said:

Sorry for the late reply, the fitting is actually M12x1.0. Regarding the picture of the wiring, do you mean the wiring for the fluid level sensor? If so, this is just a simple + and - circuit.

hey mate - question - did you use the spacer form the R35?

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      This sounds like someone who would have owned an R33 in their past... It's okay, I'm 100% picking up what you're putting down Mark.
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      Just back on what was raised about jacking off the the tow/tie down point on the front of cars. I've used it plenty. I've also watched it on a car where you could see it move the front end of the car. It was like the front end/whole car being tweaked and twisted a bit. I will say, I struggle to find good jacking points on MOST cars. The ones that have good points, I then normally struggle to find a jack tall enough to make the car change height!   One of my go to points for either the jack, or the axel stands though, is either a suspension pickup point, OR a subframe to chassis major bolting point. I actually think its the subframe on my R33 that has a bit of a bend in it, from being jacked in the middle too. However, it could have been one of my many other cars I've had over the years! Or it could also be the from me jacking it up, and the fact the top of the front radiator support isn't there, so it can allow the front of the car to move and bend etc.
    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      My apologies. I forgot we were talking about weird beard M series stuff. Had been talking elsewhere with someone about an R33 with similar subject and got confused.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, I don't like the look of ND RF, or any ND really, I don't like their faces or arses, why, because of their "modern" lines, the NC, whilst "modernish" has a more rounded shape that I like Well, that's how my overly judgemental eyes see it anyway  
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
×
×
  • Create New...