Jump to content
SAU Community

Recommended Posts

So every other image of the stagea interior ive seen on the forum has the dvd player above the glovebox and some flush inbuilt stereo in front of the shifter, my car for some reason has another entire glovebox above my glovebox, and the dvd player is instead in the centre, along with a single DIN radio and a non-popup screen. The setup was definitely installed in japan as my radio refuses to go outside like 70-89 on frequency and I cant find a manual.

image.thumb.jpeg.8645fbb776baa66bd732561caba3583d.jpeg

Would the stereo removal process be the same as the normal m35 removals on the forum or can I simply slide the single DIN radio out somehow with a tool?

Also, my antennas are like built inside my windshield and Im going to need a new windshield, how would I replace those?

Link to comment
https://www.sau.com.au/forums/topic/484101-removal-of-pnm35-stereo/
Share on other sites

On 4/10/2022 at 4:12 PM, GTSBoy said:

You actually listen to the radio?

Nah, it’s more for the sake of having the function just cause lol. 

Aux works fine but I’d much prefer to stick a Bluetooth radio or even a single din CarPlay radio that folds out or something.

I just can’t figure out how I pull the thing out as all the v35/g35/m35 removal guides I've looked at have different shaped plastic trims that don’t match up to mine so I’m weary of following them and ripping the car up for nothing.
 

Edited by oscian

Just to be clear.....none of that audio shit mounted in the dash is OEM right? It's all aftermarket Jap? In which case, if there is a tool for removing the headunit, it will be Pioneer specific. Some little thing made out of 2mm thick flat sheet with 2 prongs on it or something, to push in and release the tangs. Would only be accessible after you've removed the fascia trim from it.

Same with the Panasonic things. Just work out how to prise that trim off from around the shifter and up the dash. Probably some screws hidden in the ash tray, and the rest of it is just clipped in and you break the clips off with a small flat blade screwdriver and then swear a lot.

9 minutes ago, GTSBoy said:

Just to be clear.....none of that audio shit mounted in the dash is OEM right? It's all aftermarket Jap?

From what I can gather the radio, screen and Navi are aftermarket jap but the navi+screen is connected to my OEM reverse cam and tv tuner somewhere else in the car.
 

I’ll poke around with some pry tools and have a look then.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...