Jump to content
SAU Community

Recommended Posts

Had this this for about 15 months now.
So much it being a "quick and easy" build.
I bought this thinking I could clean it up relatively easily, get an ID check and happy days.
Man was I wrong (but we will get to that point later.
As pics go, this is how I got it.
 

240766237_411760160340571_9179066995878058681_n.jpg

240850947_884430632477911_2206592708212832329_n.jpg

241199645_219255340164243_5761876118263603355_n.jpg

240617276_1058636848298498_3014773373489578223_n.jpg

241227712_317264663528258_2776488915134456663_n.jpg

241153997_1780582492148968_8600412488012025068_n.jpg

240542063_4394474893970039_1630432812659634534_n.jpg

240877530_243292041046392_736336570535090799_n.jpg

240477772_4398657066879867_9076538937715685512_n.jpg

238914021_4264738340274562_5834007907401241430_n.jpg

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/484388-ponieboi-r32-sedan-build/
Share on other sites

First thing i had to do was to get rid of the gokart steering wheel, not sure what the go was there.
Also managed to find a sedan rear bar relatively cheap, thanks to Zac. (RB30DET, SA).
Next was sussing some of the "custom wiring" as I was relatively new to Nissans (last one I owned was an N15 SSS about 8 years ago). Nothing on the dash worked except Fuel and Speed so I was assuming all the data came from the ECU. Didn't get anywhere, future me problem.

PXL_20211029_062954167.jpg

Snapchat-103966481.jpg

20211012_192637.jpg

Managed to find some cheap wheels, and get them delivered from Whyalla for $200. I couldnt deal with the 19"G2 wheels any longer lol. I found out once I got them, they didnt fit due to bore. Listed them up for sale for $400, gone the next day. I assumed they were 4x100 / 4x114.3, turns out they were 4x110 / 4x114.3. Didn't even know that was a thing.

PXL_20211030_014633709.jpg

In an attempt to get rid of the disgusting "gauge mount", I found that you can actually run a consult cable > android tablet, and run an app called NDS. I was pretty surprised considering it is a 30 year old car. Shows data as well as Diag codes which came in handy later. Using a recycled tablet mount from my work, I rigged this up. Currently I didnt have a dock power cable so I had to recharge this everytime I used it.

PXL_20211030_021127802.thumb.jpg.260b673cbab62f37cd5f5fc4ce0daf5b.jpg

1 - headsup.jpg

Fast forward a month, I had purchased a 5 stud kit, R33 GTR brakes, braided lines, and R33 stockies.
Booked in a time at Dan Holland's workshop and we went through and chucked it all on. Also gave the engine a basic fluid service, as well as removed all signs of HICAS (not a delete, physically removed all of it and blocked off all ports).

If anyone needs any work done in Adelaide, especially on diffs. Contact Dan @ The Crown and Pinion

3 - at dans first.jpg

Much better.
4 - AFTERWHEELCONVERSION.jpg

  • Like 1

Had a few issues with idling and the tune it came with.
Took it over to Adam at Jaustech.
Updated the Nistune, made some adjustments.
Now idles fine, and also making 235rwkw.
 

Video: https://photos.app.goo.gl/YXvSgPzrrGD3ex9Q8

Sort myself a list of shit I needed to pass for a RWC, and got cracking.
PXL_20220412_112433716.thumb.jpg.b7c0dcd2be3490b38baa43c4d5368ae7.jpg

Started by cleaning the bay up. Removed the oil breather, and fitted stock looking covers on. Also painted piping black as we all know SAPOL/Regency love finding shiny things.

5 - removebreatherandblack.jpg

 

Wanted to get rid of the shitty piping set up that came on the car.
However I could not use the standard RB intake piping because the TD05 has a 3" inlet.
Took a trip to upullit, found a saab turbo inlet pipe and a 3.8L ecotec bend.
Chucked it all in, bolted up. Looks the goods for now.

6 - upullit1.jpg

7 - upullit2.jpg

 

Managed to find a center vent and steering wheel for free,
Starting to look half decent inside.
8 - steeringwheel and vent.jpg

 

Spent way too much time trying to diagnose what the wiring for the horn was, and why it wasnt working once I found the correct wire.
Ended up mounting a spare horn I found in the shed, made a new wire from the relay straight to the horn. Test and works. Happy days.
9 - horn issue.jpg

Few more months. Not going to lie the whole "Easy rego" i had planned that didnt work had me a little disheartened for a while. Needed to continue, went back to dans and fitted my new diff.
R200 LSD 4.11 out of a C34.
Driveshafts out of a R33 GTSt.
Like a glove. R180 open wheeler went in the bin.

13 - dantrip2.jpg

Continuing on prepping my butthole for a full RWC, I found a full stock exhaust with a cat for $100, as well as painted the lock bar in hope it would go unnoticed. Also did both rear wheel bearings as one was absolutely shot.
14 - stockexhaust.jpg

Also figured out the diff knocking wasnt my issue, it was the tailshaft centerbearing.
Bought one from Hardys and got it fitted and balanced at ATS (now also owned by Hardys)

15 - tailshaftbalance.jpg

No more knocking.

November 22.
Painter rings me and says he needs to re-make the whole quarter panel as its full of JB weld and bog. Great.
Managed to find a shell that's been sitting for 10 years, also non complied so I dont feel bad about cutting it up.
 

18 - spare shell.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...