Jump to content
SAU Community

Recommended Posts

Hi i was looking for some info 

on going over engine that is new to me noticed these two Items i am assuming one is Vacuum and other is Vent .. anyone have any info that could help thanks in advance .

the one with some hose and a Cap head i am assuming to be Vacuum ,.. but the other is just left open .. there is no issue with the car running etc 

 

thanks in advance 

Beaker

Vaccum1.JPG

Vaccum2.JPG

Link to comment
https://www.sau.com.au/forums/topic/484630-rb26-assumed-vacuum-lines-r32/
Share on other sites

The silicone line is probably supposed to be connected to the steel tube. The steel tube will pop out on the other side of the timing cover and is probably connected to the charcoal canister, as Meap said.

But, given that the plugged line is silicone, therefore not stock, it would be impossible for anyone to be categorical about what it is. You will need to follow it to the other end, and then compare it with the vacuum hose diagram from the workshop manual.

Hey many thanks for the comments the one with the blue silicon and the Cap head bolt in it i believe from some searching to be another Vacuum point for the Fuel pressure reg ( standard) i have aftermarket with different routing .. it would be the First pic pipe to no where i am confused about now :)

 

15 hours ago, Beaker_666 said:

Hi i was looking for some info 

on going over engine that is new to me noticed these two Items i am assuming one is Vacuum and other is Vent .. anyone have any info that could help thanks in advance .

the one with some hose and a Cap head i am assuming to be Vacuum ,.. but the other is just left open .. there is no issue with the car running etc 

 

thanks in advance 

Beaker

Vaccum1.JPG

Vaccum2.JPG

That port with the bolt stuck in it is the port that the charcoal canister uses as a vacuum signal. I don't believe it is used to purge as there's another hose that is common to all cylinders rather than just the first two. As others have said it goes to that metal pipe which looks like someone has put it the wrong way. You can see the intended routing in this picture from when I tore the intake manifold apart: 

IMG_3609.thumb.jpeg.664ced3c21d19dcb92bbdb8196ba7621.jpeg

IMG_3999.thumb.jpeg.61f326c3c2ae863d5edd914fe43b25c8.jpeg

IMG_4076.thumb.jpeg.eeb2bac4b312145e14a4f52380e2053a.jpeg

Personally I do not understand why people delete charcoal canisters on these cars when it is purely to one's benefit to not have raw gasoline venting into the engine bay and into the garage. Higher octane components evaporate first and leaving the gas tank open to atmosphere invites corrosion and moisture especially in the US where almost all gasoline has 10% ethanol in it.

  • Like 1
1 hour ago, Beaker_666 said:

Hey Cheers for the responses yeah looks like the pipe is pointing to the side rather than up .. but the Pipe on the First throttle body is being used for the Sard FPR .. guess will just will put a pipe over this one .. 

The front of the balance tube is the correct port to use for the fuel pressure regulator. It should only go to the FPR and nothing else. 

BTW, not sure if you were already aware, but an incorrectly installed vacuum tube almost certainly means your engine has been out and probably rebuilt at some stage (potentially head only). You can't get at that pipe without moving the front timing cover, timing gears and rear timing cover too which you would never bother doing for something like a timing belt change.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...