Jump to content
SAU Community

Recommended Posts

Has anyone attempted to upgrade the brakes to the 370z akebono brakes? (I already have the calipers)

I know brackets are available for the z32 and s13/s14 but I'm not sure either of those would work.

If anyone has any insight, I would greatly appreciate it as I do not know much about these cars

 

Cheers

Link to comment
https://www.sau.com.au/forums/topic/484760-s1-rs4v-brake-upgrade/
Share on other sites

Might be worth just starting with some basic measurements of the mounts and caliper height. I don't recall ever seeing the brakes swapped out before. I believe S14, R32 and Z32 all use the same mount (But I could definitely be wrong). If you can't find any other help, maybe see if you can find some measurements of these calipers to see how different an adapter would be?

Good luck, keep us updated.

I thought Z32 4 pots bolted straight on. Not sure about 370Z.

I look at rotor catalogs and compare different models.

I'm looking at upgrading my brakes at some point. Not sure what to use. I got R34 GTT rims.

I'd just bite the bullet and try one on. Can just leave the original caliper connected.

The bolt spacing for the caliper to the knuckle should be the same, but I reckon that the brick has 12mm bolts and the Akebonos have 14mm threads in them. That means you either need to the drill the holes in the knuckles or knock the inserts out of the calipers and put in some 12mm ones - which is not for the faint hearted or those without the necessary resources. If you have to ask what those resources are, guess which category you're in.

S1 stagea has the larger bolt holes in the upright, so that should be fine.

Other than potential bolt hole stuff and triming dust backing plate, I understood all S and R (and z32) are bolt on/interchangeable. It's only when they went z33 onwards that the offset was changed so that needs a specific bracket for Z33+ on R.

  • Like 1
  • 1 month later...

thanks for all the great info and I apologize for not replying sooner (did not get any reply notifications.

I am going with Z34 Akebono brakes on all 4 corners.

needed parts

Z32 Brake line brackets for the rear

Z32 front and rear brake pipes

Z32 brake hoses

Z32 to Akebono caliper brackets

Z34 calipers, rotors and pads

thanks to Frenchys Performance Garage for helping me out with the details!

 

Will upload pictures when I get around to installing them

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...