Jump to content
SAU Community

Recommended Posts

Which turbo's are you guys running on your sr20det's? 

Im looking at the:

-GARRETT GT2871R (0,64AR) - $1350
-GARRETT GT2560R - $1050
-GARRETT GBC22-350 - $850

 

Im curious about the GBC22-350, anyone tried it? 

I currently have a built sr20det (top (cams, springs, solid lifters etc) and bottom(rods, pistions, coated bearings, headgasket and main/head studs)) but dont wanna run any crazy numbers, only safe numbers to get the car running again.
I also dont wanna break the gearbox since i will be running the standard gearbox (5speed).
 

IMG_4128.jpeg

Get a GTX2860R Gen 2, it will do about 250~260kW and come all close to the side of 3000rpm on E85.

Here's a post I wrote about it: https://www.instagram.com/p/Crr_8gOyC3e/ 

3 hours ago, Dose Pipe Sutututu said:

Get a GTX2860R Gen 2, it will do about 250~260kW and come all close to the side of 3000rpm on E85.

Here's a post I wrote about it: https://www.instagram.com/p/Crr_8gOyC3e/ 

Looks great! Sounds great aswell.

 

maybe the gt2871 is the way to go then.

the GTX2860R is a bit pricey 

4 hours ago, Dose Pipe Sutututu said:

GT2871 is so old, it's not 2003 anymore.

True. But does it matter if its a good turbo? 

gbc220-350 is a newer model, but dont know really mich about them. Tried to catch someone who runs it on a sr20

2 hours ago, timmy94 said:

True. But does it matter if its a good turbo? 

gbc220-350 is a newer model, but dont know really mich about them. Tried to catch someone who runs it on a sr20

Like I said earlier, it's smaller than stock. You can just look at the numbers and compressor map to know this. Technically the turbine will flow more due to higher trim but the compressor flows less air at the same pressure ratios.

Edited by joshuaho96
6 hours ago, timmy94 said:

True. But does it matter if its a good turbo? 

Subjective, I think it's a terrible turbo when compared to today's modern offerings.

Only thing "good" about it, is that it doses very well. You get a nice suuuuuututututut lol

  • Like 2
  • Haha 1

I am now running a Aeroflow 5047 .64 rear (gtx gen2 2867 specs)

Previously ran a garret gtx gen2 2867 .82 rear

The .64 is the way to go as a lot more responsive.

I also run a stock 5 speed but its struggling and eating syncro's.
Car makes 220-270kw pending boost level.
 

Edited by robbo_rb180
  • Like 1
22 minutes ago, timmy94 said:

ok then Got offered 

 

GTX2860 or GTX2867.

can get a good deal on the GTX2860R.

shall i go for that then

Gtx2867 

If decide to go for more power will be ready to go for around 270-280kw and be super responsive. 

1 hour ago, timmy94 said:

Whats the minimum power you think you can run on that without promblems like surge etc

Surge from what? Fuel?

1 hour ago, timmy94 said:

The GTx2867 Will probably be alot more expensive. 

If money is an issue look at other brands like mamba, pulsar, Aeroflow

Edited by robbo_rb180
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...