Jump to content
SAU Community

Recommended Posts

Hello SAU,

I recently purchased an Alcon TA6 kit through a QLD company who supplies the dog bones/rotors etc. The kit has 356x36mm rotors - aluminium dog bones - TA6 calipers. I used the HEL brake lines I already have. Kit appears to be of high quality.....as much as visually i guess it can be.

What I have noticed after install and pressure bleeding (and pedal bleeding) multiple times is that the calliper is flexing a decent amount when the pedal is pushed - enough that i can push the pedal to the floor as the calliper just keeps on flexing.

Details:

1. OEM master cylinder @ 15/16" (BM44 - non ABS GTST)

2. OEM everything else on brake system - rear callipers etc. Just braided lines (front/rear) and the TA6 front kit

3. The TA6 calliper has ~2% smaller piston area than the OEM 4 pot sumitomo calliper - so no issue there.....i dont think. TA6 is 27/31.8/38.1 and OEM is 40.4/40.4

4. Have checked the calliper flex with car on (booster assistance) and off - same result just have to push harder with car off

5. Have unbolted calliper from the dog bone so its just resting on the disc and tested again - same thing - so flex of the dog bone doesnt seem to be an issue

6. Tried to measure pedal ratio as best i could - looks to be about 4.8:1 with some margin for error - ignoring the booster with 50kg of leg (beeeefy - but with booster probably fairly achievable) thats about 770psi of brake pressure which doesnt seem super high - but maybe it is?? So 75kg of leg = 1150psi.

I guess my question is - is this normal? Alcon distributors over here have been helpful but ultimately have said its normal. I feel like modulation is bad as only the first 30-40% of pedal pressure/travel does anything. After that its a mix of flex....and maybe some extra clamp force.

My old setup - Ksport 8 pots with 12 years of track work on them did not have this issue - pedal was solid. Only reason for change was a hub failure caused the disc to tear one of the callipers to bits.

Thanks SAU - any thoughts/help would be appreciated.

20240225_162029 (1).jpg

20240229_154329 (1).jpg

20240305_164723.jpg

20240410_143702.jpg

Edited by Nismo32
  • Nismo32 changed the title to Alcon TA6 Calipers on R33 GTST - Flexing

Pedal to floor is not caliper flex. Pedal to floor is hydraulic leaking/bypassing.

You quite possibly stuffed the seals in the MC when you were bleeding. A common mistake the unitiated make is to push the pedal down too far when bleeding with an MC that has been in use a long time. Crud builds up on the MC wall just past the furthest it is ever pushed in use. That crud can be hard enough to damage the seals when you push the piston down past when bleeding.

Might be time for a kit in the MC.

1 hour ago, GTSBoy said:

Pedal to floor is not caliper flex. Pedal to floor is hydraulic leaking/bypassing.

You quite possibly stuffed the seals in the MC when you were bleeding. A common mistake the unitiated make is to push the pedal down too far when bleeding with an MC that has been in use a long time. Crud builds up on the MC wall just past the furthest it is ever pushed in use. That crud can be hard enough to damage the seals when you push the piston down past when bleeding.

Might be time for a kit in the MC.

Hey GTSBoy - I used a pressure bleeder to bleed the kit - didnt do pedal bleeding at first. Issue was still there. When you push the pedal you get the caliper flex - so the fluid is going to the caliper - its not bypassing within the master itself

1 hour ago, Dose Pipe Sutututu said:

Just watched the video, that's wild!

Could it be there's some tiny air pockets in the caliper causing unequal force when the pedal is pressed?

To be fair im not sure - i have bled the system a lot of times - the pressure bleeder i use has worked a treat on previous setups on this car. So i would assume its doing the job here also......

I did also bleed with the pedal later on just to be "sure" - didnt make a difference.

14 minutes ago, Nismo32 said:

To be fair im not sure - i have bled the system a lot of times - the pressure bleeder i use has worked a treat on previous setups on this car. So i would assume its doing the job here also......

I did also bleed with the pedal later on just to be "sure" - didnt make a difference.

my bro-science approach tells me there's unequal force being applied from either side, hence the movement. If equal force is being applied, one would assume there would be 0 movement.

 

Yeah, I just watched the video also (I don't generally watch embed videos because I have to enable them in NoScript before doing so).

That's not "caliper flex" in the classic sense. Caliper flex is where the body of the caliper spread because it is not stiff enough to resist being pushed apart by the forced imposed at the piston/pad interface.

That whole caliper is moving. That probably means that the dogbone is flexing, which would point to it being too flimsy and/or simply misaligned so that the caliper has no option but to try to centre itself on the disc.

The pedal sinking to the floor would have to be unrelated.

6 minutes ago, GTSBoy said:

Yeah, I just watched the video also (I don't generally watch embed videos because I have to enable them in NoScript before doing so).

That's not "caliper flex" in the classic sense. Caliper flex is where the body of the caliper spread because it is not stiff enough to resist being pushed apart by the forced imposed at the piston/pad interface.

That whole caliper is moving. That probably means that the dogbone is flexing, which would point to it being too flimsy and/or simply misaligned so that the caliper has no option but to try to centre itself on the disc.

The pedal sinking to the floor would have to be unrelated.

I did think of this - i unbolted the caliper from the dogbone so it was just resting on the disc and the result was the same - the caliper spread about the disc. Ill do this again and get some video this time. 

I did also use a digital caliper when fitting the kit - the misalignment of the disc to the caliper was <0.5mm. The shims I have are 0.5mm so i wasnt really able to improve alignment. Seemed pretty good off the bat really.

I tell ya - this has me thoroughly confused

25 minutes ago, Dose Pipe Sutututu said:

my bro-science approach tells me there's unequal force being applied from either side, hence the movement. If equal force is being applied, one would assume there would be 0 movement.

 

This would be the only reason the dogbone would flex - pushing/pulling it based on unequal load. Not sure how to check for this besides putting a gauge on each bleed nipple and giving it the berries to see what pressure it reads.

Take the pads out, one side at a time, and see that the pistons on the padless side move properly when you press the pedal. Just to make sure that they're all doing the right thing. You can restrain 2 out of 3 pistons on a side if you need to make sure that one of them is moving. You might have too because if there is one pistons that is much easier to move than the others, then it will and they won't. Same (but opposite) with one that is much stickier than the others. You might find that one side is not working properly.

To be clear, I do not think the caliper is spreading. It seriously only looks like it is moving side to side. To spread it has to bend around an axis formed by a line through the bridge bolts (basically the line between the two caliper halves along the top. (I'd hate to think that a brand new Alcon caliper would be that bendy.) That implies the piston related problems I speculate above.

17 minutes ago, GTSBoy said:

Both sides of the caliper properly bled? I know it can be hard to convince yourself yes/no to that question.

I reckon there's a cheeky air pocket somewhere on the side facing the body

  • Like 1

Any chance you have access to a vacuum bleeder? 

(something like this)

https://www.supercheapauto.com.au/p/toledo-toledo-brake-bleeder-and-fluid-extractor-1-litre/540782.html?gad_source=1&gclid=Cj0KCQjwir2xBhC_ARIsAMTXk848QmzMiDD5_EO8X8AgI11x2F7mmv9Ty9hDU8PZPOcDBm2yNyZDVVsaAtHaEALw_wcB&gclsrc=aw.ds

I've had great success with this bit of kit, it's never let me down and its bailed out a few mates that couldn't manually bleed a stuck air bubble out. 

37 minutes ago, GTSBoy said:

Take the pads out, one side at a time, and see that the pistons on the padless side move properly when you press the pedal. Just to make sure that they're all doing the right thing. You can restrain 2 out of 3 pistons on a side if you need to make sure that one of them is moving. You might have too because if there is one pistons that is much easier to move than the others, then it will and they won't. Same (but opposite) with one that is much stickier than the others. You might find that one side is not working properly.

To be clear, I do not think the caliper is spreading. It seriously only looks like it is moving side to side. To spread it has to bend around an axis formed by a line through the bridge bolts (basically the line between the two caliper halves along the top. (I'd hate to think that a brand new Alcon caliper would be that bendy.) That implies the piston related problems I speculate above.

Good plan. I will do that for sure. havent actually checked to see that all things are happening as they should on each side of the caliper!

And yes, i agree, it seems super odd that a caliper can be so bendy. Im just struggling to find an alterante explanation.

58 minutes ago, GTSBoy said:

Both sides of the caliper properly bled? I know it can be hard to convince yourself yes/no to that question.

Yep - i went from furthest away to closest to MC - both sides of each caliper - then came back and did it again to make sure.

18 minutes ago, Murray_Calavera said:

Any chance you have access to a vacuum bleeder? 

(something like this)

https://www.supercheapauto.com.au/p/toledo-toledo-brake-bleeder-and-fluid-extractor-1-litre/540782.html?gad_source=1&gclid=Cj0KCQjwir2xBhC_ARIsAMTXk848QmzMiDD5_EO8X8AgI11x2F7mmv9Ty9hDU8PZPOcDBm2yNyZDVVsaAtHaEALw_wcB&gclsrc=aw.ds

I've had great success with this bit of kit, it's never let me down and its bailed out a few mates that couldn't manually bleed a stuck air bubble out. 

I do - but have better results with the pressure bleeder. I could try the vac bleeder and see if it gets any other bubbles out. Will see if i can find it.....got relegated a while ago!!

Looks to be  a two part problem to me. Air behind pistons on one side of the caliper and a flexible dog bone. I know all the cool kids run alloy dog bones for the added lightness but I prefer steel because I've had problems with an alloy kit before (chattering).

This sounds extreme but I'd force all the pistons right back in the bores, bleed the caliper on the bench, re-install and bleed the system again. Assuming there are no AKB springs in these?

  • Like 1
37 minutes ago, Komdotkom said:

This sounds extreme but I'd force all the pistons right back in the bores, bleed the caliper on the bench, re-install and bleed the system again

sounds like a good solid plan actually

2 hours ago, Dose Pipe Sutututu said:

sounds like a good solid plan actually

Agreed. I will do this....although not sure how to bench bleed a caliper. Will have to find some gear or use the little vac pump I have.

There are AKB springs in these. Although I feel like they are only on the large piston....although I could be wrong there. So can't push them all the way back.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...