Jump to content
SAU Community

Recommended Posts

my question is will the A/C compressor clutch automatically turn on and off as needed to attempt to maintain temp according to the cabin sensor and a/c display control temp setting?

I ask because I vacuumed my a/c system, then added about 19 oz of R134A, which is what it appears the conversion is for the approx. 540g listed on fender tag. (has proper pressure in system) A/c compressor will turn on the instant I push the ac button and turn up fan, but it appears the compressor clutch turns on and off sporadically, a few minutes on then a few off, then back on again for a few, over and over, until I turn it off... its plenty cold and smells, fine, and no leaks are detected.

I thought it may be designed to do this??
similar to how my new GMC truck automatically turns the compressor clutch on and off depending on the load required from the engine for other things, such as when I am accelerating on to the freeway, the a/c compressor clutch will turn off until I'm up to speed as we all know the a/c compressor pull a lot of power from the engine and can severely slow acceleration.

Link to comment
https://www.sau.com.au/forums/topic/485595-98-r34-gtt-ac-function/
Share on other sites

From the very first inception of heat pump/phase change refrigeration A/C installed in cars, like......most of the way back into last century..... switching the compressor on and off was the way it was done. It's only in the last 20 years or so that they have had variable output compressors.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...