Jump to content
SAU Community

Freshly rebuilt RB25DET Neo Ticking

LjB123

By LjB123,
in Engines & Forced Induction

 Share

Recommended Posts

LjB123 Enthusiast

LjB123

Posted
Posted

Freshly rebuilt RB25DET Neo, all done by the one shop except for the machining, so the reassembly/rebuild, bed in on the dyno, and final tune. So far have done just under 1000kms since getting it back, and then this tick started happening.

Was a bit quieter the other day when it started, took it to the shop to have a look, was told it was likely the VCT gear had shit itself because of where the tick was situated, and to take it home, i drove home cautiously and havent driven it since, but started it up today and it was suddenly louder and more rattly. The shop is taking it back later this week to see what the go is, has anyone else had a ticking like this? Sounds like its in the head, the spun bearing it had before getting rebuilt was a deeper knock and definitely down in the bottom if the engine, different to this, its alot higher pitched 

Thanks in advance people!

Link to comment
https://www.sau.com.au/forums/topic/485906-freshly-rebuilt-rb25det-neo-ticking/
Share on other sites
LjB123 Enthusiast

LjB123

Posted
  • Author
Posted
25 minutes ago, GTSBoy said:

Sounds like VCT actuator.

As in the solenoid? I disconnected it and still makes the noise unfortunately. The solenoid works as it should, unplugged and when 12v is applied it clicks open and closed

LjB123 Enthusiast

LjB123

Posted
  • Author
Posted
6 hours ago, GTSBoy said:

No, the solenoid is not the actuator. The actuator is on the cam gear, to make it actually move when given oil pressure by the solenoid.

Ah ok so best bet is replace the cam gear? I do have a spare low km engine with one on it. Will try replacing it with that

LjB123 Enthusiast

LjB123

Posted
  • Author
Posted
3 minutes ago, GTSBoy said:

The actuator is not the cam gear. It is attached to the cam gear. But if you wanted to swap over the whole cam gear, then that would (should, depending on the health of the spare) work too.

Ah understood. I cant find anywhere that sells just the actuator, just the whole unit itself with the gear unfortunately. Not cheap either

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...