Jump to content
SAU Community

Recommended Posts

I've recently spoken to a supplier who can get us a really good price on headlight globes.

I've used the PIAA globes, and although they look blue, they are not very bright (the bluer, the less light).

These globes that i've found are 4200 k globes, which is a perfect white. Not yellow at all. These are very bright. When compared to plain old globes, the 55 watt seems to be twice as bright, and much nicer. the 100 watt is crazy bright, and i have not had any problems with heat.

The BEST part is the price:

The 55 watt H1 is only $35!

100 watt H1 is $45.

The brand is a generic brand, but for that price, you can't go wrong. I've been using them for about 5 months, and they're still going bright and white. For the price of PIAA(which is not as bright), you can buy 4 sets of the 55w or 3 of the 100.

PM me if interested. This price is available for sydney people who are close by for pic up. Or for interstate provided there are enough to make it worth postage. Or unless if you want to pay post.

Note, supplier is doing these at near cost price.

Link to comment
https://www.sau.com.au/forums/topic/48615-bright-white-headlight-globes/
Share on other sites

  • 2 weeks later...

Hi MANWHOR3

Nice name btw. :wassup:

Like I said, I'm not the one selling them. I have just happened to find a supplier willing to do them near cost price. I was told that the extra is really only for his cost to go get them and the fact that he has to buy them in boxes of 50 pairs.

I don't have any pics atm, but will try to get some tomorrow (my car is stuck at a carpark after some @#$#@%^ at the carpark decided to let my tyres down) :)

You're welcome to come have a look if you want.

97r33gtst-typeM

Wow, how lucky is that how we're on the forumns at the same time. I guess it's pretty addictive.

You know what, like you said, you can't go wrong for that price. I'd like to get a set or possibly two today. I was hoping that maybe i could come see it, then i'll drive us down to the supplier, if it is at all possible.

I'm dying for a new set of globes. Yellow is so yuck, and not bright at all.

I've sent this to you by pm too.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...