Jump to content
SAU Community

Potential MAP Reference Point

Radical_Goodspeed
 Share

Recommended Posts

Radical_Goodspeed Rookie

Radical_Goodspeed

Posted
Posted

So I'm in the final stages of assembling my single turbo RB30/26 and had a question regarding MAP reference points. 

I've seen several recommendations such as tapping the cylinder 2/3 ITB, tapping the intake manifold at cylinder 2/3, or using a point on IAC.

First two are doable but require permanently modify part and the third is "out" as I plan to delete the IAC. 

All that to say my question is can I used the "bleeder" in the center of the ballance tube as a MAP Reference?

I'm running a catch can so I don't need it for the PCV system. My thought process is it "pulls" from all 6 cylinder, and it's between the ITB and the cylinders making it ideal for MAP reference according to what I can find.

Thoughts?

Link to comment
https://www.sau.com.au/forums/topic/486200-potential-map-reference-point/
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted

Getting a decent signal from all 6 throats is a challenge. I don't know for sure, but I suspect that the stock balance tube is not ideal for it.

I have done it on an ALFA 4 cylinder (about 35 years ago, so don't ask for too many details). We drilled 4x holes in the manifold runners, put in some fittings and ran hoses to a decent sized (I think it was about 20mm diameter) pipe that ran the length of the inlet manifold. So, it was quite a decent volume. There is a "tuning" balance to be found between the volume of the common plenum on such a thing and the diameter of the pipes running from it to the runners. You need the volume to be large enough to damp out the sharp spikes in pressure signal you get as each runner gets sucked on by its cylinder, but not so large that it becomes too slow to respond to actual changes in MAP. And you need the hoses to be small enough to transmit the signal quickly, but not so small that they delay the signal.

You might have to have more than one go at it, if there isn't any actual success based wisdom to be had here. Hopefully there is.

Anyway, I would not do it on only a couple of cylinders.

I would also not care about "permanently modifying a part". Just bloody drill holes and make stuff better. There is nothing sacred about any GTR unless it is a genuine museum piece that you shouldn't be modifying at all anyway.

joshuaho96 Veteran

joshuaho96

Posted
Posted
2 hours ago, Radical_Goodspeed said:

So I'm in the final stages of assembling my single turbo RB30/26 and had a question regarding MAP reference points. 

I've seen several recommendations such as tapping the cylinder 2/3 ITB, tapping the intake manifold at cylinder 2/3, or using a point on IAC.

First two are doable but require permanently modify part and the third is "out" as I plan to delete the IAC. 

All that to say my question is can I used the "bleeder" in the center of the ballance tube as a MAP Reference?

I'm running a catch can so I don't need it for the PCV system. My thought process is it "pulls" from all 6 cylinder, and it's between the ITB and the cylinders making it ideal for MAP reference according to what I can find.

Thoughts?

Isn't there a fitting on the back of the balance tube? That's what the OEM boost gauge uses.

GTSBoy Grand Master

GTSBoy

Posted
Posted
2 hours ago, joshuaho96 said:

That's what the OEM boost gauge uses.

That's just a gauge, with a certain amount of electronic damping, and no-one cares if it is timely-accurate. I'd hesitate to use it for an ECU MAP input without knowing that it was a nice signal. Responsive but smooth. Not laggy. Not lumpy.

joshuaho96 Veteran

joshuaho96

Posted
Posted
14 minutes ago, GTSBoy said:

That's just a gauge, with a certain amount of electronic damping, and no-one cares if it is timely-accurate. I'd hesitate to use it for an ECU MAP input without knowing that it was a nice signal. Responsive but smooth. Not laggy. Not lumpy.

AFAIK I've seen other people recommend using the back of the balance tube as well. Andre Simon from HPA at least. I can't imagine it being that far off from ideal even if it was only used to drive a boost gauge from the factory.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
×
×
  • Create New...