Jump to content
SAU Community

Recommended Posts

Hello,

 

My name if Frederick, i'm 30 years old and I live in Belgium, Europe!
I used to have a Nissan 370z daily but since I got a company car I turned that into my seattime driftcar.
About 3 years ago I also wanted something older with more feel, so I got an R32 GTST with an rb26 engine.

I am now getting the rb built to have around 800hp and it's close to being finished.
I'm very excited for how it will drive and how driveable it will be!

Regards,
Fred!

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/486265-hiya/
Share on other sites

58 minutes ago, Curlyfred said:

R32 pics
Not sure if you can upload pics directly, but i've added them through an imgur link above. :)

 

23 minutes ago, MBS206 said:

You know that discussion everyone tags you in in this section about no one knowing how many posts they need to do something... :P ha ha sorry, couldn't resist 😛

Promoted to full member so can now post pics directly.

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/486265-hiya/#findComment-8000569
Share on other sites

11 hours ago, GTSBoy said:

Do the GKTech rear lower control arm mount relocation, and either alloy subframe inserts or very stiff subframe bushes.

Traction is going to be at a premium!

I went through the Gktech catalog but can't seem to find the kit you were talking about, do you have a link perhaps? :)

Link to comment
https://www.sau.com.au/forums/topic/486265-hiya/#findComment-8000570
Share on other sites

3 hours ago, Curlyfred said:

I went through the Gktech catalog but can't seem to find the kit you were talking about, do you have a link perhaps? :)

This is the LCA mount reloctaion kit. Self explanatory in its description.

https://au.gktech.com/products/s13-180sx-r32-subframe-anti-squat-reduction-weld-in-kit?_pos=62&_fid=1e812d392&_ss=c

These are the alloy subframe bush inserts that I am using. I like them.

https://au.gktech.com/products/rear-subframe-slip-in-collars?_pos=29&_fid=1e812d392&_ss=c

Alternatively, if you have original and shitty bushes, you might consider outright replacement with poly.

https://au.gktech.com/products/polyurethane-rear-subframe-bushes?_pos=28&_fid=1e812d392&_ss=c

I would also higly recommend that you look into adjustable RUCAs and tension rods, so you can sort out the camber and bump steer behaviour, especially if the car will be any more than ~15mm lower than stock.

I would also highly recommend the GKTech FUCAs, although you really should do some research and learning on the subjetc of R32 FUCAs before making any decisions.

All of this will be criticaly difficult to get through a TÜV inspection too, if that happens to be relevant to you.

Note that if you do install the relocation kit, you will absolutely have to replace the associated bushes with spherical joints (you can read all about that on the product page) or upgrade the LCAs also.

Link to comment
https://www.sau.com.au/forums/topic/486265-hiya/#findComment-8000581
Share on other sites

17 hours ago, GTSBoy said:

This is the LCA mount reloctaion kit. Self explanatory in its description.

https://au.gktech.com/products/s13-180sx-r32-subframe-anti-squat-reduction-weld-in-kit?_pos=62&_fid=1e812d392&_ss=c

These are the alloy subframe bush inserts that I am using. I like them.

https://au.gktech.com/products/rear-subframe-slip-in-collars?_pos=29&_fid=1e812d392&_ss=c

Alternatively, if you have original and shitty bushes, you might consider outright replacement with poly.

https://au.gktech.com/products/polyurethane-rear-subframe-bushes?_pos=28&_fid=1e812d392&_ss=c

I would also higly recommend that you look into adjustable RUCAs and tension rods, so you can sort out the camber and bump steer behaviour, especially if the car will be any more than ~15mm lower than stock.

I would also highly recommend the GKTech FUCAs, although you really should do some research and learning on the subjetc of R32 FUCAs before making any decisions.

All of this will be criticaly difficult to get through a TÜV inspection too, if that happens to be relevant to you.

Note that if you do install the relocation kit, you will absolutely have to replace the associated bushes with spherical joints (you can read all about that on the product page) or upgrade the LCAs also.

That's crazy helpful!
i'll be ordering both the poly bushings and the weld in kit.

In Belgium the technical inspection can be ever more difficult than TUV, but with oldtimers (30+years old) they allow more so it should be ok I think, i'll check with some friends who work there. :)

regarding the FUCA, RUCA & tension rods, i've been learning alot about all the suspension components for my driftcar, but I should probably invest some time in how they should be set up for a grip car instead of the opposite. 😛 

Link to comment
https://www.sau.com.au/forums/topic/486265-hiya/#findComment-8000605
Share on other sites

1 hour ago, Curlyfred said:

That's crazy helpful!
i'll be ordering both the poly bushings and the weld in kit.

In Belgium the technical inspection can be ever more difficult than TUV, but with oldtimers (30+years old) they allow more so it should be ok I think, i'll check with some friends who work there. :)

regarding the FUCA, RUCA & tension rods, i've been learning alot about all the suspension components for my driftcar, but I should probably invest some time in how they should be set up for a grip car instead of the opposite. 😛 

Plenty of people I knew who drifted set their cars up more for grip than traditional "drift", and then just added LOTS of power. Gave them more control, and bigger smoke shows. :D

Link to comment
https://www.sau.com.au/forums/topic/486265-hiya/#findComment-8000609
Share on other sites

On 09/05/2025 at 7:19 AM, funkymonkey said:

Aw man, I was in Belgium earlier this month in Brussels and Bruges. Would've been awesome to see a Skyline all the way over there! I did load up on Tintin merch though :D Welcome!

Hope you had a great time here in our tiny country. :) 
The JDM scene we have here is quite small, it's mostly BMW, Volkswagen with burble tunes haha.
But the few JDM cars we do have in the scene are pretty nice. Some of my friends drive cool s14's too. :)

Both built engines, red one makes abt 500, blue one abt 400 i think?

2.png

1.png

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/486265-hiya/#findComment-8000723
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...