Jump to content
SAU Community

Recommended Posts

hey, i found a problem with your mod. that green wire is also the power wire for the demister for the rear window.once cut you will loose the demister.well its like that on my s1 33.ill have another play with the modual and see if i can cut the feed further down the line after the power has already been routed off to the demister control switch.ether that or run a new power wire to the switch so it can still operate.

Jack

ok guys i had another poke around in there,so far i havn't been able to by pass it and still keep the demister operational.i had a play with the "black box" the one that clicks when the central locking operates and found the wires that have power when the lock or unlock function is trigerd.iv yet to try it but ill try and route a wire straight to the switch on the drivers side door and triger it from there and then cut the lock triger wire on the black box so i dont loose the lock function on the passengers side door all together.on another note i found the triger wire for that anoying buzzer under the dash on the drivers side that beeps when the keys are in the ignition and the door is open.as many of you would know simply unpluging this buzzer means you also loose the power windows and what not. i havn't tryed it yet but hopfully cuttin this wire will cut the buzzer out and still enable the windows to work.

ill take some pictures and give you guys some pin outs tomorrow when the camera is charged.

Jack

  • 10 months later...

hey guys

this threadis old as but yesigot a 96s2 and mines got theauto lock

shits me cus weni have the keys in the car and i shut the car door it locks them in

mindu i do also have an aftermarket viper allarm

but they do lock on takeoff

and unlock when i turn the car off

cheers

DRIFTZY

  • 1 year later...
  • 2 weeks later...
  • 4 years later...

You lose the demister but......

I managed to stop mine, Mine was only locking the passanger door above a certain speed. One day the actuator started playing up and wasnt moving far enough to unlock the door. Mate happened to be wrecking a S2 NA R33 and I grabbed the actuator out of it. Since then the door doesnt lock automatically.

Noticed that the S2 actuator had pins in it instead of 3 like the S1. Same plug otherwise, just a pin missing

Hopefully it helps

  • 7 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...