Jump to content
SAU Community

Recommended Posts

1. What's with the v-opt.co.jp sticker? Every car seems to have it and every car seems to have it in the same place. Who are v-opt.co.jp?

2. I've noticed a lot of drift cars have only a single front windscreen wiper. Is it an expensive conversion? Why would they bother? Would this be illegal in Australia for road use?

Link to comment
https://www.sau.com.au/forums/topic/49971-questions-about-drift-cars/
Share on other sites

1. What's with the v-opt.co.jp sticker? Every car seems to have it and every car seems to have it in the same place. Who are v-opt.co.jp?  

2. I've noticed a lot of drift cars have only a single front windscreen wiper. Is it an expensive conversion? Why would they bother? Would this be illegal in Australia for road use?

1. http://www.d1gp.co.jp/

they make option and tengoku videos!

its put there because its stuck there on the D1 GP cars

2. not entirely sure on that. maybe less weight?

Option run the D1 series, part of your entry will be that you have to the sticker on the car.

It is like the Konica stickers on the Konica V8 Supercar series cars. No matter who your sponsors are if you enter the series you have to have those stickers on it.

V opt is the sponsor sticker.

Single wiper is illegal as far as I know.

Proper conversions I think MAY be ok but may require engineering.

I know people who take both off, then put their wiper at a different angle on the stock driver side bolt that turns the wiper.

This results in the wiper being in the middle of the passenger side screen most of the time - i think its stupid.

I would spend the money on doof doof or power :D

Option is a car mag for enthusiasts in japan. They've been goin since like 80's.

Dai is one of the guys who runs Option. They publish Option, OPtion2, Option3 etc, each one is for a different type of car. Option2 is a tuning mag sorta (which is what I collect). Option3 I think is for Kei cars and so on.

v-opt are video option, the AV part of option. They are the major sponsors of the D1 competition.

I'd say do whatever you want to your car :(

it's yours and who cares what anyone else thinks?? you like it and that's all that matters

Yes this is true, and we will all laugh at you...nobody does it here bar the small % of try hards. For the plain and simple fact it's only for race cars involved in D1...do you see anyone going around with F1 logos/decals or touring car decals!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...