Jump to content
SAU Community

Recommended Posts

Hi all,

Bit of a problem i'm having at the moment with my R33 GTST. Climate control is pumping hot air in, irrespective of what the display says (18 - 32degrees). Run a diagnostics and comes up with no error codes at all. I have done a search and come up with it may be the blend door but i have no idea where this is. I have no liquid in my foot wells or anything like that so i don't think it's a blocked heater core?

Any help would be appreciated.

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/50302-climate-control-only-heats/
Share on other sites

Will either be the heater box under the dash, blend door as you said, or the unit itself. The first step would be to swap the unit itself with a mate as thats the easiest job of the lot and will either fix or eliminate that possibility!

hmm....thanks for the replies. Reluctant to think it's the air con gas as in the mornings, before the car has had a chance to get hot, if i turn the a/c on, it's bloody cold so i think that's working and has gas. This just seems to be hot air constantly streaming in, even when off. The only way i stop my cabin getting hot is to turn it off but leave the recirc button on. Which is why i was thinking it was the blend door.

boj01: when you say, "unit itself", could you please carify to what you mean?

Check the outside temp sender. On my 32 a wire had come off. same symptoms as you, fixed with electrical tape.

My R33 GTS25t had similar symptoms recently, after some warranty work - which involved removing the front dash panel. Auto electrician did not reconnect the ambient cabin temperature sensor (wire + tube, I understand). This is located just to the left of the steering column - behind the panel.

It would only pump hot air (which is a system default arrangement), except @ the minimum temp setting - 18degrees I think - where it was possible to get cold air.

Dealer whipped off the panel, reconnected the sensor/s, and all was back to normal. He knew what he was doing, and only took 5 mins. Would have taken me yoncks.

Try to check whether your sensor lead/s have become disconnected, before doing anything more drastic.

good luck :D

Fixed!

It was my blend door. The little lever than actuates the door wasn't attached to the door itself leaving it on full heat the whole time. Simply put that back on and viola! All good :)

Thanks everyone for their help. :)

Fixed!

It was my blend door. The little lever than actuates the door wasn't attached to the door itself leaving it on full heat the whole time. Simply put that back on and viola!

Congrats! Well done! All very satisfying when you find and fix problem yourself, without any big bucks.

:D:):):):):cheers::cheers:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...