Jump to content
SAU Community

do s13 sr20 turbos fit a gtr

fatz

By fatz,
in Engines & Forced Induction

 Share

Recommended Posts

GTRsean Grand Master

GTRsean

Posted
Posted

With valve overlap and timing you can still get bits of ceramic into the combustion chamber. Exhaust gasses aren't continuously flowing out of the engine and in that short time when they are not you will get a neg pressure, backflow depending on manifolds, exhaust system, valve overlap etc. So, it is possible but doesn't happen to every engine!!

GTR-Ben Proficient

GTR-Ben

Posted
Posted
Hi guys, I have seen 8 X RB's with ceramic turbine failure, 2 X GTR's, 3 X R33 GTST's, 2 X R32 GTST's and 1 X R34 GTT and none of them had any ceramic anywhere other than in the cat.   There wasn't any in the turbine cover or in the dump or in the engine pipe, it was all in the front of the cat.  Blown there by ~200 cubic metres per second of ~600 degrees celsius exhaust gas, that's better than my Stihl leaf blower. :wassup:  

Maybe if you were spinning at the time and the engine turned backwards, you might get some sucked up into the manifold.  Of if you where starting the engine at exactly the time the ceramic failed and it coughed and ran backwards. :headspin:  

I don't think so, Tim :P

Well I have seen it happen on say 4-5 GTR's and a few GTS-T's.. dosn't always happen but IT DOES HAPPEN!!

Dosn't seem to happen to GTS-T's quite as much.. maybe due to GTR's having 2 turbo's and the manifold design etc makes them worse.

I will take photo's of the bore and the turbo, I though you of all people would have seen this one SydneyKid, but as you said you don't know everything.

There is always at least on exhaust valve still open it's a 4 stroke engine Roy.... so obviously the explosion is so great it sends the dust and bits up one of the open valves and into the cylinder..

Give me another explanation why there are bits of an "EXHAUST" wheel sitting in a bore in the garage at the moment.. and it got there just after it blew the front turbo up???

Over rev's and kaput.. really hoped it didn't happen to yet "another one" but the bore camera showed the truth.

All three front bores were scored.. one worse than the others.. but only the front 3, and it was the front turbo that blew?? coincidence?

People have argued this with us before.. it's not until they see it happen and wonder how there bore became so scored that they face it.

If someone can give me a good reason how the exhaust wheel magically gets into the bore other than that.. then by all means tell me!!!

But a missing exhaust wheel and the bore camera with bits of ceramic sitting in the bore on screen.. I can't see another reason.

GTR-Ben Proficient

GTR-Ben

Posted
Posted
With valve overlap and timing you can still get bits of ceramic into the combustion chamber. Exhaust gasses aren't continuously flowing out of the engine and in that short time when they are not you will get a neg pressure, backflow depending on manifolds, exhaust system, valve overlap etc.  So, it is possible but doesn't happen to every engine!!

Yes a believer! :P

Why do you people think they design split pulse manifolds.. the exhaust gases pulse.. so there is plenty of time for ceramic to get into your engine.

GTRsean Grand Master

GTRsean

Posted
Posted

Yes, I believe you because I know about engines and have also read some articles on the subject and you are correct!!

Get some time up or know what you're talking about if you think it can't happen, otherwise people get the wrong info!!

GTR-Ben Proficient

GTR-Ben

Posted
Posted

I know of people who didn't listen.. then went and bolted new turbos on before checking the engine.

Wondered why after a few k's the car suddenly lost compression and some even seized there oil pump after the ceramic went past the rings and into the oil system..

It's like a cancer really :P

I will take some photo's when we get the head of the latest victim.. this car has a fresh rebuild 3000k's ago! and low k stock GTR turbo's. He wishes he listened to me when I said upgrade the turbo's to a non ceramic.

Roy Grand Master

Roy

Posted
Posted
Well I have seen it happen on say 4-5 GTR's and a few GTS-T's.. dosn't always happen but IT DOES HAPPEN!!

Dosn't seem to happen to GTS-T's quite as much.. maybe due to GTR's having 2 turbo's and the manifold design etc makes them worse.

I will take photo's of the bore and the turbo, I though you of all people would have seen this one SydneyKid, but as you said you don't know everything.

There is always at least on exhaust valve still open it's a 4 stroke engine Roy.... so obviously the explosion is so great it sends the dust and bits up one of the open valves and into the cylinder..

Give me another explanation why there are bits of an "EXHAUST" wheel sitting in a bore in the garage at the moment.. and it got there just after it blew the front turbo up???

Over rev's and kaput.. really hoped it didn't happen to yet "another one" but the bore camera showed the truth.

All three front bores were scored.. one worse than the others.. but only the front 3, and it was the front turbo that blew?? coincidence?  

People have argued this with us before.. it's not until they see it happen and wonder how there bore became so scored that they face it.

If someone can give me a good reason how the exhaust wheel magically gets into the bore other than that.. then by all means tell me!!!  

But a missing exhaust wheel and the bore camera with bits of ceramic sitting in the bore on screen.. I can't see another reason.

Interesting...out of interest do the compressor wheels look healthy? But i suppose its the same debate, would parts of the compressor wheel make it thru the intercooler, thru the throttle body and then thru the inlet valve?!?!?!?!

Sydneykid Grand Master

Sydneykid

Posted
Posted

Hi GTR- Ben, I am truely intrigued. If the engine is a single turbo (GTST) and is doing say 5,000 rpm, has standard cams, is a 6 cylinder 4 stroke of course, the numbers mean the ceramic has ~0.4 milliseconds to travel from the turbo to the bore. That's out of the turbine cover, up the inlet manifold and get past the exhaust valve while it is open and sucking (not exhausting). Part of that journey is against the exhaust gas pressure from the other cylinders. I could work out how many kph that is, but suffice to say it is way past the speed of sound.

I could see a GTR maybe doing it with aftermarket cams (longer overlap) at lower rpm's. A straight/shorter exhaust manifold would help. And if you heard the ping and shut the engine down, maybe.

Possibly that's why I have never personally seen it, we just don't have GTR's (or GTST's for that matter) with upgraded cams/manifolds and standard turbos. Plus they always let go at big rpm on the circuit, at full throttle and the drivers don't back off either.

Very interesting...........

You are right, ceramic is nasty stuff, makes great grinding paste. :mad:

GTR-Ben Proficient

GTR-Ben

Posted
Posted

Well it's usually on GTR's with stock cams etc.. just intake, exhaust and around 1 bar.

I don't see it on the GTS-T as much, I think because they don't handle boost as well that would pop the turbo, and being a single turbo. Most people upgrade to a VG30 or similar and run less boost.

What about taking into account the speed the turbine wheel is spinning at when the engine is doing 8000rpm? 10-50X more?

The last car wasn't under load when it blew though.. so I would say boost wasn't that high it was purly revs. (2WD clutch drop in snow..)

We don't keep the stock turbo's with mods over filter and exhaust.. but there are still quite a few GTR's down here getting round with stock turbo's. We did push them out to an 11.6 on one GTR before they popped (this was the first time we saw contamination and were very confused)

I am actually scared to drive a GTR with stock turbo's these days.. I just see $$$$.

Any other ideas on why.. ?

Sydneykid Grand Master

Sydneykid

Posted
Posted
Well it's usually on GTR's with stock cams etc.. just intake, exhaust and around 1 bar.

I don't see it on the GTS-T as much, I think because they don't handle boost as well that would pop the turbo, and being a single turbo. Most people upgrade to a VG30 or similar and run less boost.

What about taking into account the speed the turbine wheel is spinning at when the engine is doing 8000rpm? 10-50X more?

The last car wasn't under load when it blew though.. so I would say boost wasn't that high it was purly revs. (2WD clutch drop in snow..)

We don't keep the stock turbo's with mods over filter and exhaust.. but there are still quite a few GTR's down here getting round with stock turbo's. We did push them out to an 11.6 on one GTR before they popped (this was the first time we saw contamination and were very confused)

I am actually scared to drive a GTR with stock turbo's these days..  I just see $$$$.

Any other ideas on why.. ?

The turbine blades should never exceed the speed of sound, the mini sonic boom would destroy them. So I don't think speed is the answer. Maybe they let go big time and then shed little bits of ceramic over the next few times the engine is started. When you fire it up to put it in the workshop, on the trailer, stuff like that maybe would be a problem on a GTR.

It certainly isn't a problem on a GTST, I have seen one driven 200 k's home after a turbine failure, it only had ceramic in the cat. I know because we took the head off while the turbo was being done and did some porting and polishing. It was clean as a whistle inside.

Bottom line, I don't know :)

GTR-Ben Proficient

GTR-Ben

Posted
Posted

We make sure when we pop them to shut them off straight away and get a tow. Just incase the turbo did go through the engine.. every second = major damage. :)

So it all happens at the same time in one big boom.. wheel is there the first second, next the engine is full of abrasive crap..

It's just one of those things.

And for those of you with stock turbo's reading this.. be careful. Please have your engine checked after you blow a ceramic turbo. :D

GTRsean Grand Master

GTRsean

Posted
Posted

I just pulled off both turbos off my r32 over the weekend and need to find out what spec these actually are. They are NOT! N1's as I was told they were and this car had been running 1.3 bar for who knows how long. The bearings are bushes and they have ceramic turbine wheels that are in as new condition. Just the bushings are worn.

I need to find out what these are off. An r32, or a r33.

Here's the specs: Compressor A/R 42, Turbine A/R 64

BB 0102J, 14411-24U10, 466089-6C

Any help would be excellent as I'm deciding what to do with the turbo's.

Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Duncan's V37.......race car?

      By Dose Pipe Sutututu · Posted

      Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • GTSBoy
      R33 persistent issues. P/steering and lag/misfire

      By GTSBoy · Posted

      What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
×
×
  • Create New...