Jump to content
SAU Community

Recommended Posts

  • Replies 148
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

  • 1 month later...
just wondering do u cover the hole lot? or just the steam of it?
I have read the previous replys and and not sure where exactly you are putting the epoxy glue on the pack.

If you look at my 4th post, I have posted pictures of where to put it.... doesn't get any easier

You guys are confused about the whole silicon thing.

What you want to do is spray the coils liberally with silicon spray

It's an aerosol lubricant, looks & feels like oil, repels moisture superbly - not a curing sealant.

I had an arcing coil issue some time back, now whenever I change the plugs I spray the coils liberally and hey presto no more probs. If you're hellbent on a more permanent fix, why not tape them up with (are u ready for this) self amalgamating butyl tape. Goes on like leccy tape, then heat with your paint stripping gun etc, et voila fuses together and shrinks around the coil insulating and waterproofing it.

When I was contracting for Sydney Water we used this stuff on external electrical connectors on sensitive datalogging equipment that was mounted inside sewers - not an electronics friendly environment. High temps, lethal caustic gases and flooding are the norm.

Should be able to get this stuff from Electrical wholesalers, Blackwoods etc.

M'kay ??

  • 2 weeks later...

Yeah, but I would be inclined to coat the inside with the goo that Telstra use for cable jointing to repel moisture. I don't know it's proper name - but it's clear & has the texture of grease. I reckon leccy wholesalers would have it.

Just thought I would update this thread with some more info....

Although my coils were covered in araldyte, they started playing up again on the weekend, so I pulled them out including spark plugs to see what was going on....

Well first of all, my tuner gapped my spark plugs like so:

1:0.6mm, 2:0.7mm, 3:0.7mm 4:0.75mm, 5:0.6mm, 6:0.6mm

not to mention a whole bunch of bolts missing all over the place, but anyhow, once they were re-gapped I turned to the coils.

Upon inspection the araldyte looked fine. No cracks, no chips.

So I took the rubber boots off, and the little springs inside the shaft and notice the shafts were a little corroded (that blue/green crap you get on your battery terminals). So I sprayed the shafts with WD40, and cleaned them out with steel wool. The car runs better than it ever has now, and is very smooth.

So also take this into consideration when looking at your coils.

Z

You've raised a good point, Zahos.

moisture seems to play more in the faulty coil/misfire scenario than many of us had previously thought. I revived one dead coil and brought two DOA's back to life with silicon spray, and noticed the same corrosion @ the spring terminal. I still reckon heaps of gooduns get tossed, where the real culprit is condensation.

My 2 zloty

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Bummer...yeah i "need" something to "ease" up the work and for my driving it would be enough.    Iam counting the tune "without" turbo. I do not mean "cheap" like something from Temu around 200 USD, "Cheap" is something around 1000 USD? 
    • Starter motors used to use the weight of metal (magnets) to provide torque. Now they use (more) current instead. This. It's completely normal.
    • So thing that had me stumped, but I think is OK....is that when it was up in the air, in neutral I had it running to bleed to coolant while I put the wheels back on. I noticed the rears were turning (slowly) which I'd never seen before 20250928_163512.mp4     Because there had been an issue with clutch slip due to pedal adjustment on the dyno, I assumed there was still and issue so spent some quality time upside down under the dash adjusting the pedal....but no matter what I did the wheels still turned in neutral. Even disconnected the master cylinder to pedal rod and same. In despair, I even removed the clutch slave so there was no chance of any preload causing it.....still happened. So either: 1. Something is not right in the bellhousing, or 2. Its a thing sometimes with cold, thick gearbox oil Internet says it might be 2, I hope so!
    • OK, few more things sorted and it is ready for a shakedown on 10-Oct, with one weird thing. Changed the run in oil and filter for the good stuff. 8l came out, about 8.5 went in with filter so that looks all good. Changed the starter (again), this time for a brand new one, works good. Interesting that the Taaaarks one is shorter than factory but spins harder, I guess electronics have moved on a little in the last 30 years. Will be nice to have a bit of extra space under there. Put the timing cover back on, and noted where the cam gears were set as a record.  Will need to double check the timing but it is pretty close. Also put the coil pack cover and intake snorkel back on. Exhaust Inlet Changed the water out for coolant, bled up nicely. Removed the rear brake pads (well worn factory sumitomo ones!), gave the hardware a good clean and reassembled. I've put bendix XP on the back again because the price is excellent at $150 a set and they worked well on the V37. Front pads have plenty so no issue there
×
×
  • Create New...