Jump to content
SAU Community

Recommended Posts

hey

i was told people here are friendly and helpful =P

been looking at a few different ways of setting up a sound system in my car... and all of them are pricey ¬_¬

one of the other things on my wish list is an ipod however.. so i was thinking perhaps the possibility of setting up a nice amp (not top shelf but not a cheap pos either) to interface with an ipod... that way i get the best of both worlds >.>

ive seen a few gimmicky setups that use a similar method, interfacing an ipod with a stereo but looks unsightly and dodgy =S

im not really one who knows alot about car audio and what is the best way to do things etc... so was hopping some of the seasoned veterines could offer some advice..

cheers

Link to comment
https://www.sau.com.au/forums/topic/51148-ipod-stereo-setup/
Share on other sites

all u have to do is get an 3.5m --> 2rca adaptor, stick one end into the ipod and the other into your amp/head unit input.

just remember the ipods amp(for the headphone socket) is a peice of crap and u wouldnt want to use that output. u have to get a cable that connects to the bottom of the ipod with a female 3.5m plug on the other end. this non-amplified output is much cleaner than the headphone output.

although it still is not good.

I've seen two ways of doing this.

Both ways involve a decent head unit, and personally if I was going to the effort I would not bother doing it any other way than properly.

The first is using the dock that you can buy for normal use. ie. the dock is designed to a. plug your firewire in for recharging and b. plug in RCA outputs to plug into your stereo (or in this case your HU).

You just use this, obviously you can't plug in firewire to power your ipod (if you find out the proper voltage which I can't remember off the top of my head I think you easily could however), but more importantly you use the RCAs and plug them into the extra port of your HU. In my case, this is done through buying a converter that converts RCA plugs into the special cd stacker input at the back. I think this converter is like $30 or $50 max from the US (worst case scenario).

I'd be going down the above path.. the cost is basically RCA cable, ipod docker and RCA>CD-in converter. And if you want your car to charge your ipod you'll have to figure that one out yourself but basically it just needs to get the dc power of whatever voltage it is and then you would hook that up to your firewire out on your dock.. It's been done before too (google).

The second is the alpine method, I assume its the same sorta thing but I haven't messed with it, nor do I really know how it works.

http://www.alpine-usa.com/products/leading...ch_kca-420i.htm

Good luck. If you need any help with the method I've described lemme know.

cheers siksII and someonestolecc

definately something for me to check out there >.>

one of the reasons why hooking up an ipod appeals to me more is that i can go from sitting infront of my pc -> car -> somwhere else, without interupting my music

but it sounds like alot more effort than i first thought and effort.. well.. meh =P

cheers tho.. definately alot there to push me forwards >.>

Don't get me wrong, once it's setup its easy. I mean the last stereo I setup it has 3 RCA inputs that can be "high jacked" without taking anything out. This allows for easier plugging stuff up.

It's the same sorta thing, when you install youir HU you just use the CD-in converter thing (I know it works with Pioneer type cd-in thingies but I don't know about other brands). And once you mount your dock somewhere you can slot in your ipod (without it falling out when you brake or go round a corner and hitting you in the head) its all done.

From there you just run into your car and put the dock in, press CD/input on your headunit and thats it.

Shrug just remember (i just thought of this now) the ipod would be a fairly nasty missile so where you mount it should be safe and secure.

GoodLuck!

There is a wiring diagram on this forum somewhere showing how to connect an AUX input to Pioneer headunits (which beats paying $100.00 plus for the proper Pioneer cable).

I did this and it cost me less than $5.00 for the wire, connections, etc. I have run the cable from the back of my deck, behind the dash and into my ash tray. Originally I had my iPod dock sitting in my ash tray and I just jumped in the car, sat down, docked my iPod and off I went.

Two problems with this though:

1. If people see the iPod dock in your car, chances are they're going to break your window to look around for the actual iPod unit. I should probably add that you cannot close the ash tray with the dock in position.

2. My iPod got scratched to shit.

So, I ended up cleaning my iPod with BRASSO to remove the scratches and then I bought an iSkin, which protects the unit and looks preeeetty damn good too. Only problem with the iSkin though (which I realised after I had bought it) is that the iPod will not dock with the skin on. Considering I bought the skin to protect the iPod in the car, removing it each time I wanted to use it in the car wasn't really an option.

I ended up taking the dock out of my car and just having a plug sitting in my ash tray. When I get in, I open the ash tray and plug in my iPod via the head-phone socket (sounds just like line out to me). Easy as pie and 5,000 songs (plus a bit of pr0n) in my car. And when I'm not using the iPod, I close the ash tray and there's no sign of the installation at all.

Sounds like the setup I'm talking about.

Did you notice any sound degredation without using the dock?

Depending on the rest of your stereo I believe if it was really good you would hear the difference but I"ve never heard it so I'm only assuming.

In my not that good setup I can hear the difference when I burn audio cds from 128kbit and 192kbit. *shrug*

  • 2 weeks later...

I was doing this with my the old GTSt. I had run into a problem where the headunit needed that special CD Changer to Line-In adaptor and I had to order it from JVC. It took more than 4 months to arrive and by the time it did arrive I had sold the car.

The adaptor cost 100 bucks by the way.

Anyway for the GTR I will buy a headunit with RCA inputs.

I was doing this with my the old GTSt. I had run into a problem where the headunit needed that special CD Changer to Line-In adaptor and I had to order it from JVC. It took more than 4 months to arrive and by the time it did arrive I had sold the car.

The adaptor cost 100 bucks by the way.

Anyway for the GTR I will buy a headunit with RCA inputs.

For sure. Forget all the hassle with converters and sh1t. Any good head unit has an auxillary input these days. I bought a sony one nearly 2 years ago that has three, 4 volt RCA out puts and an auxillary RCA input. I can plug in my minidisk player, or whatever and just select "aux" and away you go.

Richard

  • 2 weeks later...

For those with Alpine decks with AiNet connections:

http://www.crutchfield.com/S-YtslvXITD9d/c...fo&i=500KCA121B

Then just plug a male RCA cable with 3.5mm headphone jack in to it, and you can plug that in to your ipod.

I'm about to buy the bits to do this. Sure, I don't get control of my ipod through my deck, but I can always set up playlists on the ipod and then use one of the ipod remotes (not the wired remote) to change tracks, just velcro it to the steering wheel or something :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity.
    • 100% the factory sender is tapered, that is how it seals (well, that and teflon paste or tape)
    • Thanks folks - I've saved a few links and I'll have to think of potential cable/adapters/buying fittings. First step will be seeing if I can turn the curren abortion of a port into something usable, then get all BSPT'y on it. I did attempt to look at the OEM sender male end to see if it IS tapered because as mentioned you should be able to tell by looking at it... well, I don't know if I can. If I had to guess it looks like *maybe* 0.25 of a mm skinnier at the bottom of the thread compared to where the thread starts. So if it is tapered it's pretty slight - Or all the examples of BSPT vs BSPP are exaggerated for effect in their taper size.
    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
×
×
  • Create New...