Jump to content
SAU Community

Recommended Posts

Hey guys,

Wats up with that horseshoe at wakefield. It says u should be at 80 setting up for that horseshoe so that means u should be taking that HS at 80 km/h?..

Im sitting on 3rd gear at this point.

Ive run that track twice now and also 6 20min sessions each. And the highest ive tacken that corner is at 65km/h The thing is that is my slowest part of the track and is the main problem point in attaining a good time.

BTW im running coilovers and 17x9.5 inch pirellis.

Any suggestions?.

Link to comment
https://www.sau.com.au/forums/topic/52537-the-horseshoe-at-wakefield/
Share on other sites

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

i cant believe you have time to look at it!

i really dont get much time to look at the tacho or speedo on that corner so i cant really comment on the speed through there!

what times are you getting around there? what does the car do on that corner ie understeer early/midcorner/exit or oversteer?

where do you turn in on that corner? i try to stay right out and turn in at the access road coming in there on your right!

:confused: I have no idea what to suggest, other then you may be screwing up the corner entry to the keyhole by coming out of the quick left hander preceding it all wrong.

I have no idea how quick i go thru there other then i have good few revs in 3rd, so perhaps dont take the left hander so quick/wide which will leave you on the right side and speed for the two right handers that follow.

Oh and dont forget the curbs and even a few inches of dirt either side constitute the track so use all of it:)

Ive set it up alroght for the turn preceeding it. I have quick glances on the speedometer as im turning out of the wide corner. My times are 1:17 and so forth unoficialy.

I get plenty of oversteer. Whilst trying to cut back thru the middle apex and swinging the back out. To connect to the next racing line. Hmmm.

My mate in his FWD type r can hammer thru it at 70km/h.

hmm just remember that a FWD car should be able to have a better entry speed than most RWD cars, so it really depends on when the 2 of you are looking at the speedo!

1:17 isnt bad at all, especially after only 2 times down there! will take some time out there and it is a good suggestion by Duncan to get out there with the club and see how others are taking that corner!

might have to head down there in november, got some good tyres for the car now, im looking to break into the 1:14's next time down there.... see how we go

man.. i think im gonna be recovering from the one past (financially) for the next 3 months at least. Rotors, brakes and rear new tryes need replacing and also new clucth.. :burnout:

Still will also hope to get into the 1:14's as well soon. But why does it always seem to be so much harder to get that 1 sec off?.. LOL

yeah true, only got 8/10 sec to take off, but i know how you feel.. i go through brakes every time i go down there! i've had to drive back with no front brakes twice... using the HB to slow down and gears ... not fun!!!

i've always run cheap sime tyres - they last forever.. not much grip though :)

only things im missing now is running slicks to decrease the time. But fcuk i wanna see wat i could do with street tyres. Yeah on the way back all the boyz had to use the HB b/c the brakes were all gonseskiiiii... Mies was all the way to the bottom to stop.. LOL

Hey do u guys know of this old guys there that owns a amg merc.. that did like 1:12's. The things had slicks on and looked stock as. He was driving that 100k + car around like it was on rails.. Overtaking everybody. My mates says he is there often. Who the **** drive a merc amg around like that?.. LOL

AMG and M's are should be thrashed on the track. It's always good to see that stuff. Like walking through back through the city after work one day saw a PHAT GT3 parked with all towing rings on it and stuff. Thought he was a poser but looked closer the whole insides were ripped out, had buckets, harness and the CAMS required blue triangle at the battery sticker and such.

That put a smile on my face.

Ceffo you have to take me to WSID soon when I get my steering and clutch cylinder problems fixed.

Ceffo you have to take me to WSID soon when I get my steering and clutch cylinder problems fixed.

hahaha u nut - When u go to WSID thats where the problems start. Blown gboxes, turbos going, clucth frying, tyres fcuked. :wassup:

Still why drive a performance car when u cant see how much fun having in it.

I just gotta get me some 17"s or something.

hey, what size tyres are you running now....

i have worked out with a couple of saloon cars to get their 2nd hand race tyres pretty sheap per set -- they are 16" 225's

we could work something i reckon!

Guys just to let you know I run a Formula Ford with a Data Logger.  My speed around that corner is in the high 70's.  I run 64 - 65 sec laps.

haha that blows my 70-90 theory lol! I guess I'm always looking when I've left the corner not when I'm in in.

What speed for turn 10? and turn 2? this is fun :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...