Jump to content
SAU Community

A31 Tie Rod Ends - Same as R32 or S13?

jaik

By jaik,
in Four Door Family & Wagoneers

 Share

Recommended Posts

jaik Mentor

jaik

Posted
Posted

Guys n Gals, I cant get access to my car atm but I need to order replacement tie rods.... Im not home at the moment so I cant check my FAST software.... so does anyone know off the top of their head if the A31 uses S13 tie rod ends or R32 tie rod ends ... as far as Im aware theyre different.

Thanks!

JK

Link to comment
https://www.sau.com.au/forums/topic/53402-a31-tie-rod-ends-same-as-r32-or-s13/
Share on other sites
Ceffo Proficient

Ceffo

Posted
Posted

on the weekend i went drifitng and managed to do the front LHS (passenger side) lower control arm/sway bar and also the stabilizer arm (i brok eem right off). Went to the local import halfcut place and found out these were the same identical to the r32 gtst ones and got em for 300 bux.

I also noticed teh tie rods were also teh same size as well.

Ceffo Proficient

Ceffo

Posted
Posted
Hahahahaha!  I didnt find that funny until you quoted it!  HAHAH!  Classic, made my day!

hahaha.. yeah was funny till i coulnt counter steer in time (lack of damn power steering didnt return the steering wheel in time) and my car landed on the kerb. :skull:

The undercover copper was right there when i drifted around the bend. He saw the whole thing. HAHAHA

CC rocks around the corner behind me to find the car on the kerb.

Told him it was a "mechanical failure" that i somehow managed to go sidewayz around the bend at 70km/h in peak traffic and land on the bend. Still he was a top bloke thou let us go. Heck he had no proof anywayz.

someonestolecc Grand Master

someonestolecc

Posted
Posted

Lol ceffo -

you have a bad memory :tool: :P

He suggested that "noone else was involved, no property damaged, if you can get it towed I dont have to call highway patrol."

He was a top bloke and had PLENTY of proof. ie. copper being a witness is as good as 5 witnesses.

You're just downplaying how lucky you was.. if it had been me I would have been getting butt****ed right now. :whip:

Either way I'm glad it ended how it did now we can live another day and-

:rave:

Mase Mentor

Mase

Posted
Posted
You're just downplaying how lucky you was.. if it had been me I would have been getting butt****ed right now.  

Either way I'm glad it ended how it did now we can live another day and-

bahahaham funny stuff.

A fair few months back we went drifting in an industrial estate in brissie. We had been hitting this truck turn around (hairpin) all night. I got a tad ****y, came out of it and kept trying to go from side to side up the street, ended up in a ditch on the side of the road.

Cops came and i said, my car broke down and i forgot to put my handbrake on and it rolled down the hill. He tried the "you can tell me mate, i am a car enthusiast as well, except i like v8's" I kept to my word and we got our names recorded and I was left to feel sorry for myself in peace!!!!!

Funny stuff!!! But my poor lil onevia need a bit of cosmetic work after that! lol, still needs some

  • 8 years later...
esky_mad Proficient

esky_mad

Posted
Posted (edited)

Copied & Paste this from NS.com

s13 tierods are 12mm, and the shortest of the lot

s14 tie rods are 14mm and are slightly longer, but can be used in s13 but are around 10(ish) mm longer
s15 tierods are 12mm and are longer than s14 for some reason, tried them in a s13 but had monster toe in.
r32 have both 12mm and 14mm tierods, so you need to check before you buy, and SHOULD be the same length as s13

Surprised know one has actually stated that Cefiro's only use M14. Unless you are using an S13 rack of course.

Edited by esky_mad

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...