Jump to content
SAU Community

Recommended Posts

Yeah its been going pretty well. Check out www.youtube.com/boscharc.

Good weekend for you guys in the end! Get many k's on the Stag?

Nah, the stag sat in service for most of the weekend, as we also had a triton and a 200 series with trailer so srove around in them.......Yeah I have watched 90% of those vids, good stuff! Berry was a very lucky man in that accident. Sandy is stoked, we didn't have too many major drama's with the cars and winning the SARC is always going to be a good result.

Spotted that silver M35 again on Targo Road in Toongabbie yesterday afternoon, and I've been seeing it there regularly now - it's a stock-looking 250RS, standard 6-spoke wheels, no special custom rego plates or anything.

spotted a black (S2??) at Robina Town Centre, parked on the mezzanine level at around 6.30pm tonight. Had exhaust, lowered and R34 GTR-look wheels and big stickers across the rear window... Anyone on here? Never seen that one before

there was a phat as hell white C34 park on the side walk out front of Jap Link on Parramatta Rd this arvo around 2:00-2:30pm

Ryan (Bodella) and I were both there last night in each of our own cars.

Oh, could it have been the one we had on the Stagea 15th Anniversary cruise, Theo? A white S1 260RS with black TE37 wheels?

i just got mine and live off ballarat road... keep an eye out for a black rs4s

Were you in the City yesterday by any chance?

I saw a very near black Series 2 C34 RS4S on Collins St @ 5:15pm yesterday arvo. I was on a red/white R1 with a mate on a Repsol Blade just in front of it at the lights.

I've been seeing a black RS4 in my street for the last 2+ years ( which is what got my attention to the stag ! ) lowered , black , black rims , nice exhaust , sweet ride ! Oh and randomly I see a yellow s2 c34 not sure what model . Oh lisarow (central coast )

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...