Jump to content
SAU Community

Recommended Posts

Would spraying too much water onto your intercooler make it heat up the charge air?

I have 2 sprayers on the cooler which sprays water controller by a 6psi hobs switch...

Its a front mount cooler avo stage 2

Any ideas?

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Can not understand how it could be possible but someone else may want to confirm this.

From a physics perspective, unless the water is substantially hotter than the cooler it will always cool more due to the evaporative effect.

Yes unless you are heating the water by running the water lines 2 close to the engine or exhaust manifold the water will cool the intercooler not heat it up!!

How have you got ur system setup? Are you using the rear window wiper motor for the ic spray?

Guilt - toy, I just posted a message expressing interest in getting a water spray for my cooler - I would definitely think it would have a cooling effect, especially in hotter weather. Evaporating water combined with wind can substantially reduce the temp of an object. Try it on your skin with saliva (Assume the saliva is the same temp as your body). Lick your hand and blow on it. Does it feel cool or hot?

Would spraying too much water onto your intercooler make it heat up the charge air?

I have 2 sprayers on the cooler which sprays water controller by a 6psi hobs switch...

Its a front mount cooler avo stage 2  

Any ideas?

You want the mist to be as fine as possible. On my subaru, I had a water spray set up that used very fine nozzles. The way it was set up, a very fine mist was sprayed in the the bonnet scope in front of the intercooler. The water would vapourise as soon as it touched the coooler or even before, therefore cooling the air.

I have seen a few people do tests on the track. Someone found that garden nozzles which used about 1L/min actually cooled the intercooler much less than misting nozzles which used one twentieth of the water.

When I set mine up, I used three brassnozzles designed for evaporative cooling which I imported from the US. The nozzles are made specifically for cooling sports stadiums and the like.

If anyone is interested, I still have the whole kit inlcuding nozzles, adjustable hobbs pressure switch, relays, switch and a custom made electronic controller which holds the pump on for 5 seconds after boost drops (keeps the pump going between gears). I'm willing to sell this kit as I no longer need it.

Hi Mik,

you had your kit installed on your wrx correct? And with the stocko top mount cooler? How would this kit go on a car with a FMIC?

Do you have pics of the setup?

Cheers,

Scott

You want the mist to be as fine as possible. On my subaru, I had a water spray set up that used very fine nozzles. The way it was set up, a very fine mist was sprayed in the the bonnet scope in front of the intercooler. The water would vapourise as soon as it touched the coooler or even before, therefore cooling the air.

I have seen a few people do tests on the track. Someone found that garden nozzles which used about 1L/min actually cooled the intercooler much less than misting nozzles which used one twentieth of the water.

When I set mine up, I used three brassnozzles designed for evaporative cooling which I imported from the US. The nozzles are made specifically for cooling sports stadiums and the like.

If anyone is interested, I still have the whole kit inlcuding nozzles, adjustable hobbs pressure switch, relays, switch and a custom made electronic controller which holds the pump on for 5 seconds after boost drops (keeps the pump going between gears). I'm willing to sell this kit as I no longer need it.

Hi Mik,

you had your kit installed on your wrx correct?  And with the stocko top mount cooler?  How would this kit go on a car with a FMIC?

Do you have pics of the setup?

Cheers,

Scott

I had it with the stock TMIC.

It will work fine with a front mount, just need to suitably place the nozzles. The nozzles create a large amount of mist. From memory, ach is designed to cool an are of 10 squae meters or something in a sports stadium.

I have attatched a couple of pics of the nozzles.

Included is:

* 3 brass/stainless steel nozzles

* Power switch

* manual override switch

* Adjustable Hobbs pressure swicth

* Electronic control Box

* Power relay to drive pump

* Some hose

All you might need is a little hose if there is not enough there.

IMHO cooler sprays are a waste of time on a street car. In short bursts coolers work more like heat sinks than heat exchangers. That is, they absorb heat on boost and return this heat back to charge air off boost without actually radiating it to air. There isn't enough time to heat the cooler right through unless going hard for long periods. This is different to a track/race car which is on boost most of the time, which has good cause for a spray.

Also most of the effectiveness of the spray is from evaporation (hence the fine mist), so they are rendered useless in high humidity eg. BrisVegas. In BrisVegas a home ducted evaporative air conditioner would be better described as a fan.

IMHO cooler sprays are a waste of time on a street car. In short bursts coolers work more like heat sinks than heat exchangers. That is, they absorb heat on boost and return this heat back to charge air off boost without actually radiating it to air. There isn't enough time to heat the cooler right through unless going hard for long periods. This is different to a track/race car which is on boost most of the time, which has good cause for a spray.

Also most of the effectiveness of the spray is from evaporation (hence the fine mist), so they are rendered useless in high humidity eg. BrisVegas.  In BrisVegas a home ducted evaporative air conditioner would be better described as a fan.

wouldn't it minimise heat soak when you are sitting @ the lights?

This is a simple way of doing it.

http://www.skylinesaustralia.com/forums/sh...ead.php?t=52508

Cheers Rob

The nozzles used there won't do much for cooling, but will waste water.

The water needs to be made into a VERY fine mist to promote evaporation, as that is what causes the cooling effect.

I still dont think the guys question has been answered. He is asking is TOO MUCH water bad.

And out of interest how bad would it be to put say metho or something similar in the water mix? As this would bring temps down even lower correct?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Sorry to hear your HFM BM57 was faulty,  did you contact HFM I would hope they would be at least grateful for the information if there was some sort of manufacturing fault, you would hope they would be sympathetic even if your item was 2 years old if it had never been fitted. May I ask where it leaked from ?
    • Cats are called Bella, and Donna...  Like that poisonous plant And I remember your 2 monsters, I remember making a little bit of wee when you let them out... LOL I have already installed cat doors into the laundry where their kitty litter is, and the sun room, apart from the cat doors there's not going to be any permanent mounted stuff on the interior walls (interior doors are cheap and easy to replace) I will get a outdoor cat cage thingie once I finish the landscaping out back... https://catnip.com.au/ The only off limit areas are the main bedroom and the gym room....but, currently the cats are curled up in bed, in the main bedroom with the Mrs.....LOL, the off limits for the kittens to the main bedroom lasted about 5 minutes with Jackie I currently only have 1 free standing huge cat tree multiple level scratching post thingie in the lounge room, but, I will be getting another one soon now that I'm happy with the furniture layout in the back room and have a perfect spot for it  
    • All of this is making it seem clear that running the Coppermix twin was definitely the way to go, especially in hindsight with how insane tariffs have gotten and the strength of the USD vs yen at the time.
    • That sounds like no chance of even importing one for road registering then Now I see why Duncan wants to check LHD rules for Targa...   I wonder how "bolt in" the AWD would be if you got one imported from the US and swapped it to an AUD one
    • Not to mention they drive like a bucket of bolts! yuck!
×
×
  • Create New...