Jump to content
SAU Community

Recommended Posts

I was wondering does anyone know of the most powerfull RB25DET in Australia or even some very powerfull ones in japan etc, Has to still be 2.5 L doesnt matter what engine mods internal bolt ons, just after some recorded figures maybe dyno sheets or info from mags, just lookin to see who owns the record, thanks heaps for the help

Keep on boostin :P

Link to comment
https://www.sau.com.au/forums/topic/54068-most-powerfull-rb25det/
Share on other sites

Theirs lots of potential out their.

Just a couple off the top of my head,

OBHVE R33 - 386rwkw's 518hp

JMS R33 - 448rwkw's 601hp

Twin turbo RB25 Silvia - 355kw's

A fair few guys on here have 300kw + GTS-T With RB25's in them some with aftermarket internals some with standard internals.

Im sure theirs more powerful RB25 engines than above that havn't been seen to the public. :) It also comes down to $$$ aswel :)

But at the end of the day horsepower figures will only tell the truth on the 1/4 mile.

:)

Jun

From the thread:

MOD LIST:

- NEO RB25 (year 98+)

-Greddy intake plenum

-75mm mustang throttle (to be upgraded by a 83mm infiniti one)

-Greddy Type R S14 intercooler with 3in. piping

-custom exhaust header (ceramic coated)

-Presicion Turbo T-67 (front polished, rear ceramic coated)

front: .70ar with a 66 turbine

Rear: .69ar with a P trim turbine

-Turbonetics racegate

-HKS blow-off valve

-850cc injectors

-aeromotive fuel press. regulator

- Walboro 255 in-tank fuel pump

- Fuel canister (to maintain fuel volumen)

-Bosch porsche fuel pump ( after the canister)

-custom fuel rail

-Rb25 stock tranny

-exedy dual disk cluth

-nismo differential

-3in down pipe and 3in exhaust (no cat.)

-Microtech fuel injection computerEngine is totaly stock internals, for the exeption now of a power enterprise head gasket and ARP head studs.

587HP @ 26psi

I need more convincing that what is in that thread :)

Having said that and a bit of research on this Turbo

(look here: http://www.precisionturbo.net/turbocharger...ategory_id=3027)

The Presision T-67 is rated at 780HP

Thats one big F'off turbo.

That'd be one laggy ho

the jms R33 448rwkw was a dyno failure, the car actually did around 380rwkw with racing juice and low 300rwkw with pump. I saw it got tune again and run after 1,2 weeks after the autosalon.

yeah, always have to be careful of dyno figures, especially from "workshop" cars funnily enough.

anywhere from 250-300rwkw is fairly "standard" these days... quite a few getting around australia with these figures.. .could probably name about 10 on here with those figures alone :)

The question is - what fails first? and what are the inherent weaknesses when pushing past 300rwkw ?

i got 420rwhp of an rb25 using a gt35 with pistons as only internal upgrade, as for bolt on the list starts here and goes to over ---------------> there, but it did lasted for a fairwhile until i drove a true 800+ hp rb26 monster.

This isn't meant to sound provocative, but I am tired so I apologise in advance if it does sound that way.

near anything an RB26 can do an RB25 can also.

Is that really saying much though? Throw enough money at most half-decent engines are you can extract significant power.

How does it break down in terms of bang-for-buck (ignoring initial purchase price)? Surely the RB26 starts with an advantage?

LW.

ive got a mate with a neo6 in a 180, its currently making 290rwkw detuned. if he ever gets it finished ill post the end figure up. yet to come is bigger fuel lines (still using stock s13) bigger throttle body and cams. no point in posting what is expected so ill wait till it makes the power befor saying anything else.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...