Jump to content
SAU Community

Recommended Posts

  • Replies 237
  • Created
  • Last Reply

Top Posters In This Topic

So what you are saying BBQ is that i have bigger injectors and im not telling you becasue i like the grief that you non believers give me. Dont get your knickers twisted because the Wolf computer has far superior fuel management than any other compter full stop. But all of the "doubting Thomas's" here will never know, i dare you buy a wolf, tune it and see.

Donnon and Ellis from HPI are wrong and they are not god, sorry to disappoint you all.

13devil. 350km to a tank around town gettting on it a fair bit.

love to you all, no doubt i will see all of you in perth shortly

PS. if there is anyone in perth who does not believe me pm or reply here i can show you.

My only objection your last post is that your suggesting that Wolf can somehow increase the flow through an injector over say a PowerFC. How is that gonna happen?

And i know your gonna say something about batch fire, but its relevance to this discussion is limited at best. Batch fire has what i consider to be absolutely no relevance on RB engines.

Im sorry to have had to add my 2c but saying that wolf can magic up extra fuel is rubbish. Its like saying your new toaster makes your stereo louder.

the Wolf computer has far superior fuel management than any other compter full stop.

Give me a break! :bahaha: All the ecu does is turn the injectors on and off, for the programmed amount of time (duration) at the programmed time (timing). There is no magic there, 6 light switches do the same job. :idea:

Line up the Wolf with a Motec M600 and tell me where the Wolf has ONE advantage. It is slower, has less load points, its sensitivity is deficient, the current carrying capacity of the injector drivers, the ignition drivers current capacity, the ability to handle F&W and S&N lambda sensors, the closed loop response, memory capacity, the data logging speed, lambda range, lambda resolution, RFI immunity, battery transient protection, fuel calibration accuracy, ignition calibration accuracy, number of outputs, number of inputs.........I think you get the drift.

A small tip....you are not dealing with people here who simply/blindly accept things. If you truly believe it is superior, then you have to state why. If you don't know, then find out. NO ONE here is going to believe you otherwise.

:)

and thats why the Wolf ECU is generally first choice for raceteams worldwide over Motec. Pfft!!!!! The only problem with Motec(in my experience) is that many installers don't really know how to extract the most potential out of it, compared to say some simpler ECU's ummmm Wolf! Don't get me wrong, I'm sure the wolf is good and offers great value for money, but to say it's the best is a little ill informed and optimistic don't you think.

so let me get this right.

Donnon works for Willall Racing. The owner of willall racing/industries owns australia's fastest GTR on street rubber at 8.83 @ 157mph? Donnon works for Willall and knows nothing?

haha ok

He didn't say they know nothing. He implied they lacked some knowledge specific to the wolf ecu, when they wrote it up.

Sydneykid,

On the otherhand if he has the power he's got and he's got standard injectors, can we come up with a reason why it works. I'm not a regular customer of SST and I'm as skeptical as the next guy but, Magic1's car does do what he says it does and it has got standard injectors.

your right batch fire has nothing to do with it. why open shut and open and injector. why not leave it open through the shut 'batch fire' part?

because thats what smokes the coils in injectors... an injector running over 90% d/c will get too hot and eventually fuse its coil.

this thread is pretty tense! im not taking any sides but...

why not do a public demo and swap the injectors in front of everyone for some stock ones and repeat the power on a dyno? i even have a set id donate to a 3rd party to make sure they are fitted!

sounds like a hassle i know but it will make or brake your claim!

i know if no one believed me id either prove them wrong or shut up

magic

Again congrats on your archievement .....

But please dont talk crap about how good the wolf is..... its a gameboy compared to the motec.

Either magic is a wolf salesman, or he is repeating the crap the salesmen that sold him the wolf told him :bananaman

Its comments like this imacul8 that make people think your a clown.

No its true what IMACUL8 was point to the fact of the wolf computer cant magically make a stock injector perform like a injector of the size of 550cc or larger, even tho the guys name is 'MAGIC"

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...