Jump to content
SAU Community

Recommended Posts

Chucked my R33 on the Dyno tonight for the first time since i got it. On low boost (0.5 bar) it made a 256rwhp :P. Then after trying to find out how the hell the Blitz EBC worked we managed to get it to do a run on 1.4 bar and and it made 320rwhp at the rev limiter!! This was due to how we had set up the boost controller, so its not really at the cars max power. We were short on time and never ended up fiddling further after this run and left it as is for now :D. I'm real chuffed anyway and i just had to tell the world :rofl:

Link to comment
https://www.sau.com.au/forums/topic/56314-dynoed-my-car-4-the-first-time/
Share on other sites

yeah its got a fair few things done. Its a hks GT2835R turbo with the 0.64 exhaust housing, greddy plenum are the main things things, plus the usual stuff like after market ecu and intercooler. I'll scan the graph tomorrow at work and post it up.

I saw 1.4 bar and thought arhhhhhhhhhhhhhhhhh.....

No mention of aftermarket turbo at that stage....

Plus he said going from .5bar (which is pretty much standard) i thought poor little thing...

Good work tho... Nice boost controllers... Ive gone from apexi avc-r to BLITZ SBC-i-D III

hey i was wondering...would you need a special manifolds for the HKS 2835R ? coz i was thinking of getting one for my r33 GTST but unsure if they would fit bolt on.

my hks 2835 uses a 0.71 exhaust housing but is a t25 flange

Will bolt on if its T3 flange

the dump pipe is a totally different flange. I just started pulling it apart so i'm not sure what time it does at the drags and probably won't get to find out for a while.

my hks 2835 uses a 0.71 exhaust housing but is a t25 flange

there's about 10 different version of this turbo. Mine is the GT2535R Pro version. Has internal gate, 0.7 comp cover, and 0.68 xhuast housing with a T3 flange. Its on the HKS website -> My Turbo I have the HKS exhaust manifold so i'm not sure if it would bolt onto the standard manifold or not.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...