Jump to content
SAU Community

Recommended Posts

hey guys i have got a half cut for sale r34 neo engine rb25det comes with engine loom gear box computer pritty much everything to make it run :P engine is in good condition pics will be up asap earily next week

RB25det neo 5speed manual

wanting 3.5k

0402670354 or [email protected]

if anything else is needed off the front cut dast front windscreen fron gaurds front strusts

post up or email :)

cheers guys

Link to comment
https://www.sau.com.au/forums/topic/58929-fs-r34-neo-engine-package-35k/
Share on other sites

Are you going to convert an r33 to r34 ? what about the rear ? wouldn't it be better to sell the 33 and buy 34 , then you will have the real thing .

Thats what i'm in the procces of doing .

Anyway good luck with the conversion .

it is a 5 sp manual :cheers:

no i got a uras conversion kit for a r33 i am selling and i have found a hlaf cut to source out the parts depending on how much this front cut sells for with all the peices will deternian how much the nose conversion will be

you guys have all seen silvias and 180 have s15 nose's now you can upgrade the skyline ones with this kit it is very cheap considering the firs for r33 in australia :)

also would like to say radiator fan shourd everything will go with the engine if any one want front console dash steering wheel front seats i think inculed  plz post up or pm me a offer :(

Hi I have and NEO RB25DE.....will that engine be a straight swap?

  • 1 month later...
yes engine mounts will bolt straight up

Hi do you still have this engine available?

any pictures? i live in sydney, how can i get the engine if i decide to buy?

so the engine is complete? turbo, ECU, wiring loom etc?

Thanks

hey guys it has been some time since i posted in this thread as .... when i first made the thread there was no interest i will have to go cheak out the engine and see what bits have been taken off but it will be a slow process as i am busy and it takes 2 hours to drive down to the factory ... the uras kit may still be avalible

sigh:(

Could you tell me how the mounts and mounting points compare to the rb20det in r32 gtst's?

i have a rb20 in my 260z using stock mounting points - want more to happen when i use my right foot:).

You dont have to bother replying if you dont want to, i wouldn't be able to buy for a few weeks or months due to having to repair the few thousand dollars a theif cost me

  • 2 weeks later...
  • 1 month later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...