Jump to content
SAU Community

Recommended Posts

Here are a few new pics of the new paint, plus of few more little changes.

Hope u all like it!!! Tell me what u think?

My "OOR33" Skyline GTS-t ---> 'Show & Go'

Performance/engine mods: Garrett GT30R BB high-mounted Turbo, Stainless Steel exhaust manifold, HKS style external wastegate with screamer pipe, SARD 550cc injectors, Bosch 720hp fuel pump, GReddy e-manage ecu, Blitz FMIC with custom stainless piping, Blitz sus power pod filter, 3" exhaust with custom dump pipe, Turbosmart type 2 BOV, Cusco front strut brace, GReddy Profec B II boost controller @15psi...317hp @ wheels.

Exterior: Paint - Full Respray in Standox: Daytona Paradise (green/blue/puple mix), Carbon Fibre bonnet, Bodykit - GTR wing/side skirts/pods, Tommy Kaira front bar - modified, Vault Savannah 18" chrome wheels, KYB shocks, DBA front slotted rotors, Nismo clear side indicators, tinted windows.

Interior: Dash surrounds/vents painted in Standox: Daytona Paradise, HKS turbo timer, Apexi Rev/Speed Metre, boost gauge, MOMO millenium steering wheel, alarm. Full Sony Stereo: CD player, front & rear 6" speakers, 6 stacker, 12" sub in box, 500w amp.

Link to comment
https://www.sau.com.au/forums/topic/59639-my-xmas-pressie-new-paint-job/
Share on other sites

hows the auto r33 going for ya? ever think about converting it into a manual ?

Auto is great - love the driveability, the quickness off the line without wheelspin & also the money i will save on clutches when i start racing it down the quarter!!!

So 2 answer ur question NO, i have never & will never think about converting it 2 a manual - wish more ppl could realise the benefits.

For the drag strip, the auto is king, manuals can still have a good run down the strip

For circuit, manuals are king, and i would hate to think how an auto goes around a track...

In traffic the auto would be much better, but the overall control of the car goes downhill with an auto, less in control...

Paintjobs different, i'll give you that... but the wheels ruin it...

For the drag strip, the auto is king, manuals can still have a good run down the strip

For circuit, manuals are king, and i would hate to think how an auto goes around a track...

In traffic the auto would be much better, but the overall control of the car goes downhill with an auto, less in control......

i agree with u 100%, i hear what ur saying.

i like most ppl understand the benefits of a manual, but most ppl do not understand the benefits of an auto.

2 put it in perspective - i hear often "r u going 2 convert it to a manual" i would never ever hear if it was a manual "r u going 2 convert it to an auto"

the conclusion is most ppl think a manual is better, i disagree, that's all

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...