Jump to content
SAU Community

is this right on my GTR???


Recommended Posts

sorry guys this could be a silly question but i recently (about a month ago) bought an R32 GTR 94 model stock as a rock and loving it and 2 weeks after i got it, it was given a major service inluding , timing belt, oil, oil filter, fluids. diff oils, transfer case oils, everything and anything that could be replaced pretty much was.

so any way i havent really been booting it as i am trying to adjust to the more of a race car feel then the luxury comfort feel (that my previous R33 GTST offered).

But Yesterday i gave it a fair bit of stick here and there and parked for about 15 minutes then had a 20 minute drive home of average speed 100 as i live in the country and theres no traffic lights but pretty much no booting at all just like a normal sunday car cruising, and when i arrived home there was a funny smell and when i opened the bonnet the engine BAY (not just the engine) were extremely hot. the actuall stand that holds the bonnet open was to hot to hold.

Now is this normal??? i notice that there really isnt much room for the heat to be released in the engine bay, but i was just cruising for a good 20 minutes so the cool air should of pushed through some where.

just finally the oil that was used was that magnatec stuff, my dad says, cause the oil sticks more to the inside of the engine it could be holding the heat a lot more than a normal oil that will run down to the sump alot quicker.

thanks all any help and advise would be greatly appriciated.

Link to comment
Share on other sites

Aslong as the engine didnt overheat then there wont be any damage, sometimes the entire front of the car can get heatsoaked from engine/brakes etc its fairly normal

oil could be a factor, personally i wouldnt use magnatec, its not really designed for high performance turbo engines

Link to comment
Share on other sites

the oil does not stick more, it is not magnetic

to hazard a guess and that is all it is i would say it is normal, air moves at different patterns at different speeds and a hot spot in the engine bay is easily created. best to hear what others with GTRs have to say

Link to comment
Share on other sites

I know my car can get quite hot too, its only a GTS. I think thats the way with most imports as they run hotter i think (in a way)... thats probably not true, but they do tend to keep the heat around the engine bay for quite a while (my mates 33 GTS-t that he just bought he was driving it around throughout the day and night - joy rides cus he jus got it) anyways, he woke up the next morning to find that the engine was still warm to touch, not hot in anyway but definately not cold.

Link to comment
Share on other sites

rb26dett are known to generate a great deal of heat even when you are cruising leisurely... go motul or something else other than the magnatec stuff.

if you think thats bad... wait till you done 2 laps at the track.. the oil temp needle will be sitting at 12 o'clock easily. sump and oil cooler is the proper way to go :rofl:

Link to comment
Share on other sites

WHat was your oil and water temps like? they are the main things i look at.... also as others said, get rid of the magnatec, i don't think its fully synthentic?

I use Castrol forumula R fully synth 10-60w

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Any chance you can get a Nistune board installed instead and set the speed limit to whatever your tires can handle?
    • Hi all, I need to get this HKS SLD attached to my stock ECU because I've now got the German autobahn and faster European circuits to contend with.  The car is a manual 2dr ER34 with an AT ECU and I've realised the AT ECU has two pins for speed sensor signals: Pin 29: Vehicle speed sensor signal (Vehicle speed sensor 2) Pin *58: Output shaft rotation sensor signal (Vehicle speed sensor 1) - *RB25DET A/T model only Before I go butchering this harness, is anyone sure of which pin is the correct one for signal adjustment? The attached document from HKS indicates pin 29 but I found this situation mentioned in the following thread on a different forum (R34 GTT Auto Trans Speed Cut Problem | Zerotohundred) mentioning pin 58 needing to be altered by member zephuros, albeit it seems to be for an RSM-GP and the info appears to be old.  R34_All_Workshop_Manual-pages-2.pdf R34_All_Workshop_Manual-pages-3.pdf R34_All_Workshop_Manual-pages-1.pdf HKS SLD Vehicle Pin out P59-P70 ER34-pages.pdf
    • Slimline sub on the rear parcel shelf is doable. Pioneer TS-WX140DA is only 70mm high.   
    • People like Johnny Dose Bro might be laughing at my post because I accidentally added 100mm to my numbers. 350-355 is indeed the lower limit. 450 is off-road Skyline spec.
    • What is the "compromise" that you think will happen? Are you thinking that something will get damaged? The only things you have to be concerned about with spherical jointed suspension arms are; Arguments with the constabulary wrt their legality (they are likely to be illegal for road use without an engineering certificatation, and that may not be possible to obtain). A lot more NVH transmitted through to the passengers (which is hardly a concern for those with a preference for good handling, anyway). Greatly increased inspection and maintenance requirements (see above points, both).   It is extremely necessary to ask what car you are talking about. Your discussion on strut tops, for example, would be completely wrong for an R chassis, but be correct for an S chassis. R32s have specific problems that R33/4 do not have. Etc. I have hardened rubber bushes on upper rear control arms and traction rods. Adjustable length so as to be able to set both camber and bump steer. You cannot contemplate doing just the control arms and not the traction arms. And whatever bushing you have in one you should have in the other so that they have similar characteristics. Otherwise you can get increased oddness of behaviour as one bushing flexes and the other doesn't, changing the alignment between them. I have stock lower rear arms with urethane bushes. I may make changes here, these are are driven by the R32's geometry problems, so I won't discuss them here unless it proves necessary. I have spherical joints in the front caster rods. I have experienced absolutely no negatives and only positives from doing so. They are massively better than any other option. I have sphericals in the FUCAs, but this is driven largely by the (again) R32 specific problems with the motion of those arms. I just have to deal with the increased maintenance required. Given how much better the front end behaves with the sphericals in there.....I'd probably be tempted to go away from my preference (which is not to have sphericals on a road car, for 2 of the 3 reasons in the bulleted list above), just to gain those improvements. And so my preference for not using sphericals (in general) on a road car should be obvious. I use them judiciously, though, as required to solve particular problems.
×
×
  • Create New...