Jump to content
SAU Community

Recommended Posts

if youre running a gtr, how hard is it to run rwd? im in the US and we didnt get any freakin Skylines.... sucks here..... and so ive heard what people THINK you need to do in order to run rwd. is there a basic toggle switch that can allow you to take all power from the front wheels and send that power to the rear? or do you have to actually pull the front axles? just somthing ive always wondered. thanks fellas.

Link to comment
https://www.sau.com.au/forums/topic/62597-gtr-rwd/
Share on other sites

different ways of going about it depending on which model you have. Best way is to probably get a torque splitter. If you have a 32 just pull the 4WD fuse. On a 33/34 things get a little more complicated as pulling fuses isn't enough, you'll have to also disconnect the driveshaft to the front wheels as well.

Which model are we talking about in particular?

Link to comment
https://www.sau.com.au/forums/topic/62597-gtr-rwd/#findComment-1179362
Share on other sites

You do realise the GT-R is still a RWD, that intelligently supplies some drive through the front wheels? Unlike the WRX which is constant AWD (primarily a FWD with some of the drive sent to the rear).

If you don't want AWD, then don't get a GT-R.

Link to comment
https://www.sau.com.au/forums/topic/62597-gtr-rwd/#findComment-1179380
Share on other sites

Only the STI spec-c has the electronic torque distribution though right? Anyway the GT-Rs AWD system is different in the R32,33 and 34. You certainly can't specify how much to the front and rear but you can turn off the front. I think that this is mostly a reflection of the age of the GT-R. If you search you'll find quite a few topics on disengaging AWD on each model.

Link to comment
https://www.sau.com.au/forums/topic/62597-gtr-rwd/#findComment-1179550
Share on other sites

Only the STI spec-c has the electronic torque distribution though right? Anyway the GT-Rs AWD system is different in the R32,33 and 34. You certainly can't specify how much to the front and rear but you can turn off the front. I think that this is mostly a reflection of the age of the GT-R. If you search you'll find quite a few topics on disengaging AWD on each model.

exactly what i was wondering. i wouldnt get a GTR if i didnt want awd... who wouldnt want awd? but in the rare case that you wanna drift for whatever reason and want to have rwd, i was just wondering how hard it would be to do that. thanks for the help fellas.

Link to comment
https://www.sau.com.au/forums/topic/62597-gtr-rwd/#findComment-1182690
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...