Jump to content
SAU Community

Recommended Posts

  • Replies 84
  • Created
  • Last Reply

Top Posters In This Topic

changed my gearbox oil today, had real trouble getting the feed bolt out, finnally got it out wit a breaker bar.. the bottom bolt had a fair few metal shavings on the magnet, cleaned it up nicely, doesnt look like any previous owner has ever changed it, put VMX80 in and running it in now..

only 2L of oil came out of my gearbox, is this normal? as ive read up here that there is supposed to be about 3.8 to 4L?

Edited by MKDR33

heslo if u havnt got a breaker bar, try wrapping an extension power cable around ur ratchet, put it in position and lock it in and have someone pull onto it from the front of the car while you push from underneath, it worked for my mate..

i have some stuff from repco in my box (85w/140) in my gearbox

its awesome shit, thick as and not too bad when its cold

just did my mates car also yesterday wtih the same shit, its good

both rb30e gearboxes behind rb30e's

  • 2 months later...

ok after a few crunches I decided it was time for a gb oil change. Not sure which one to use but after read a few posts it came down to the Castol SynTrans and Redline MT90 - Mt90 as numerous people have had issues in the longer term with the shockproof. Cos I was just going down to Bursons who stock both i found that the Syntrans was $29 per 1lt bottle and the redline was $34 per gallon (0.946l) or $123 for the 4Gl (3.78l) bottle. I wanted 5L cos I wanted some left over for top up later and anyone who has used reldine know you will have some left over...cos of the bottle sizes.

As I use the Redline motor oils in both my R33 (10W40) and my FTO (10W30) I went with the MT90 which cost $149 all up from Bursons with no special discounts etc for 5GL.

I ended up putting in around 4.0 ltres after a good drain. Ran it up and its seemed ok - time will tell.

As for the drain plugs etc...bit hard..the fill plug needed my extendable 1/2" drive rachet which I use for my wheel nuts...came off a treat when extended like 1m. :laugh:

Filled using a pump i bought ages ago for this task...cos $12 I think.

All up for $150...high grade oil in the box now I can slam though the gears and get the most out of my 300kw.

THanks for all the info. never pay some1 do do this job for you!

mind u I have a pit in my garage...makes every quite easy.

  • 10 months later...
  • 1 month later...

Putting the Redline stuff in is fine guys but just remember that it is only masking the fact that your gearbox is probably worn and will continue to getr worse... Start saving those pennys!!! I just rebuilt my box (R33 RB25DET - 1993) and it cost me a bit.... If you have a series 2, it's not too bad but there are some parts, ie. sliding hubs, they don't make anymore for series 1 and there are heaps of other major parts that need to be replaced when you put in the series 2 syncro...

Anyway, that's my 2 cents....

jayson i had the redline shockproof in mine $25 a L mind u

and now i have the same stuff u have, and mine crunches slightly into 2nd when cold

the redline stuff was great... next time in gonna buy some again

also when i refilled it i poured it through where the gear lever goes... didnt seem to do anything wrong that way... makes life easier i fink

anyone got any probs wif the way i did it?

  • 11 months later...

ARGHHH i couldnt get the dam filler or drain plug loose, its like a bolt with a sqaure socket, there lso tight and i think glued in aswell, my 2,500kg jack is broken atm too so i had to use the wheel changing jack and then use clamp stands, not enough room to get in, looks like im gonna have to take it into the mechanics to get the dam bolts loose, or just dig a pit in my back yard lol.

anyone from sa who could get my plugs undone? ill pay with a slab of beer :P

  • 1 year later...
  • 2 weeks later...
  • 5 months later...

hi all I have a 33 gts-t with 86000 on the clock and would like to change the gearbox oil not because there is anything wrong but because I like to change all the oils when I get a new car.

I was going to get the synthetic nulon 75w85 ($29.99 per liter) but everyone here recommends vmx80 which is much cheaper. castrol recommend vmx-m 75w85... someone said nissan run vmx80- from the factory is this true? i dont want to run a mineral if there is syn in there already thats all.

also the castrol website says 2.8 liters... is this wrong is it infact 3.8 - 4? can you overfill it?

  • 2 months later...

It's only going to come out of one hole and the other one is a filler...you can't drain from the wrong hole :)

When filling up, fill through the filler hole until it starts to pour out of the filler hole.

Easy!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...