Jump to content
SAU Community

HELP ****ed Radiator

MFC05

By MFC05,
in General Maintenance

 Share

Recommended Posts

Cubes Grand Master

Cubes

Posted
Posted

Similiar to what happened to my sisters VL after the flush.

Only difference was before the flush it wasn't overheating, after it was. :cheers:

I pulled the radiator out and when reverse flushing with compressed air and water I had what felt like bark chip covering my hand. It was massive bits of scale that had blocked the core. :(

The Dan Grand Master

The Dan

Posted
Posted

That may be the case. It might not be the head but how pissed would you be if you spent all that money doing all this other 5hit and then find out it was coz a fake mechanic couldn't do a simple test.

How does he know it's not. Has he got Xray vision or something. A dye test will pick up the smallest leak that won't even cause your car to overheat.

Well anyway, I'm done with the advise. If you choose to ignore it, that's your choice. Like I said before, it may not be the head. I hope it isn't. I hope it's something simple to fix because I have gone through all of it hundreds of times. I just believe that it is best to cover all bases so that you rule out all possibilities. To say that it is not a particular problem without performing the tests to prove it is just foolish. I really hope they do the right thing by you.

MFC05 Experienced

MFC05

Posted
  • Author
Posted

Well i like to say 3LIT3 FORS3 WAS right.... and i should of done he sed...!!

it was a blown head in my engine !!! ****en bullshit !!!!!!!!!

so now i got a quote from ADD racing to get it done for 1200

wat do u guys reckon of that price??? any places in brisbane that will do it cheaper ???

and what does it inovole wen changing a new head ?????? pullin the engine out ???

The Dan Grand Master

The Dan

Posted
Posted

You would get change from $800 if you did it yourself. Plus without knowing the condition of the head it is impossible to give an accurate quote as if the head is bent it will cost $600 to get a full head service and straightened. Now I'm sure even if you got the $450 VRS set for free, you would still not get away with $800.

Worst case scenario is:

Full head service $600

VRS $450 (assuming you can buy the VRS seperate from the full kit which is $600)

Labour - 9 hrs - $500

Oil and filter change - $50

Coolant - $30

Timing Belt - $80

Plus you have to account for broken exhaust studs, hylomar spray and any vacuum lines or hose clamps that may break while doing the job.

Total worst case scenario is: $1730 approx

If you can get a second hand head that is already straight or the head you have is still straight, the price would then drop to $1250 plus the cost of the second hand head if so required.

If you do it yourself you would save the $500 labour so then it would drop to $750 for a straight head and $1230 for a bent one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...