Jump to content
SAU Community

Recommended Posts

i have it - jap and eng version

whats up ?

Software was purchased, installed, registered and connected OK to my ECU without a hitch, however when I tried to connect it to two other 'pexi ECU's it failed to establish a connection.

I spent a fair bit of time trying to nut it out and it appears to be just the other two ECU's that I have an issue communicating with. So I guess my question is: Is the software only licensed to run on one ECU, or is it the two (non-communicating) ECU's being of a different model/type?

The software works seamlessly with my R33 GTR, so my belief is that the issue lies with the fact that the R34 GTR and R34 GTS-T's Apexi ECU's are not compatible with the R33. The only way I have to determine if the problem lies with a license issue or with a software version issue is to get another R33 GTR with the same ECU as mine (about as easy as it sounds).

This is where you come into it :D . In your travels have to come across the quick answer to this question?

some updates tonight - has been a while...

removed the user content section - it was crap

updated version info & version matrix

updated "does the unit work on auto cars"

updated manual links for user manuals

updated "what is the fc pro & do i need it" - included identify fake fc pro versions

updated "How does the AVC-R compare to the PowerFC boost controller kit?"

good update today

updated "I have the older PowerFC that did not come with a hand controller can I buy a new hand controller separate and use that?"

updated "Does the PowerFC have limits?"

updated "Help! My car doesn't start once I've installed the PowerFC"

updated "Where can I get my PowerFC tuned and how much will it cost me?"

updated "My idle is really crappy and it hunts around a lot when on idle. What can I do?"

updated "My fuel economy is terrible and I just had a complete tune, Whats wrong?"

updated "Boost display without the Boost Control Kit?"

updated "Hybrid Apexi PowerFC models and mix n match models, can it be done?"

updated "My Skyline R32 GTR has a wierd misfire problem, what's wrong?"

updated "Is there a replacement hand controller screen?"

updated "I have fried my PowerFC. Is it fixable?"

updated "How do I debug knocking, how can I make it go away?"

updated "PowerFC Pro - Launch Control"

updated "I want to go EPROM/Firmware hacking, Tell me how"

Software was purchased, installed, registered and connected OK to my ECU without a hitch, however when I tried to connect it to two other 'pexi ECU's it failed to establish a connection.

I spent a fair bit of time trying to nut it out and it appears to be just the other two ECU's that I have an issue communicating with. So I guess my question is: Is the software only licensed to run on one ECU, or is it the two (non-communicating) ECU's being of a different model/type?

The software works seamlessly with my R33 GTR, so my belief is that the issue lies with the fact that the R34 GTR and R34 GTS-T's Apexi ECU's are not compatible with the R33. The only way I have to determine if the problem lies with a license issue or with a software version issue is to get another R33 GTR with the same ECU as mine (about as easy as it sounds).

This is where you come into it ;) . In your travels have to come across the quick answer to this question?

this is certainly possible - have a look at the product matrix to find out if its supported by your version of FC pro & cable

alright i have now installed a power FC into my car and im having a issue im not sure if it due to the power fc or what

when i give my car the boot then take foot off the accel and put on clutch now and again my car will stall but soon as i let foot off clutch starts up again (like push starting it)

has anyone had this issue mind you it is in a evo so i doubt alot of you have

hi robert,

this can happen if you dont do the self idle adjustment properly

can you confirm you did this correctly?

also i assume you have std bov etc and not an atmo unit ?

if its blank unplugged or loose cable

if its locked on the apexi logo wrong hand controller version

if its locked on a blank screen (but lit up) then loose connector, damaged connector or damaged hand controller

Hey,

I have a RB26DETT FC D-Jetro on its way from nengun and i have the field one touch connecter from greenline. A mate (the_mafia) is re-wiring it to suit my rb20det r32 gtst. He has done the conversion with a normal fc but never djetro.

My current mods

3" turboback

2.5" split dump

GCG Highflow Turbo

Turbosmart boost T

HKS Pod

Walbro Fuel Pump

Fuel Pressure Reg (going to be removed with ecu install)

Splitfire Coilpacks

Plazmaman Forward intake plenum

hybrid fmic

plazmaman piping kit

when ecu goes in (already have waiting)

GTR injectors

3-4" intake pipe

Now we have extablised i can use a vacuume line from under plenum and T off to 2 map sensors. What im wondering is i have read the map sensors need to be spliced into standard loom for airflow meter... so do we cut off plug, and just splice 2 new wires to each existing wire in the airflow meter loom.

Also air intake temp sensor. Where does it go... have been told this will make tune much easier. So basically is there an aftermarket option (bosch) or something that is cheap or should i source one new from nissan?? Will i need to weld any nipples onto piping anywhere or what?

And now for the acc valve. I have a hose going from that to my intake pipe (behind my afm) for now and i have been told i can just put a little breather filter off the valve and leave it at that with the fc... and it will work fine, is this true.

Factory oxygen sensor... should i replace it... i have been told they should be done every 40,000km and my guess is mine is still factory one. I have also been told i wont need it with djetro and it would be a waste of money... in that case can i plug off the dump pipe or should i just leave it or should i replace it.

thanks alot if you could answer these questions. Yes i have read the faq but i could not find too much relating to my issues in depth.

cheers, Leon

Question

*2x R33 GTST Series 2 Skylines

Car A: Has Apexi PFC and Z32 AFM

Car B: Has stock ECU and stock AFM

How simple is it to swap these 2 items between cars as car A is going to be sold and taken back to stockish state. Can we just simply unplug the wiring harness from the ECU's, swap them around and plug right back in and should be fine to drive?

*Cars A and B both have stock turbo's and almost identical modifications (FMIC, 3" turbo-back, fuel pump)

Also, unplugging the PFC and moving to another vehicle... with this retain the tune or reset all settings?

Cheers,

Ryan

Question

*2x R33 GTST Series 2 Skylines

Car A: Has Apexi PFC and Z32 AFM

Car B: Has stock ECU and stock AFM

How simple is it to swap these 2 items between cars as car A is going to be sold and taken back to stockish state. Can we just simply unplug the wiring harness from the ECU's, swap them around and plug right back in and should be fine to drive?

*Cars A and B both have stock turbo's and almost identical modifications (FMIC, 3" turbo-back, fuel pump)

Also, unplugging the PFC and moving to another vehicle... with this retain the tune or reset all settings?

Cheers,

Ryan

if you do a direct swap one for one it should be ok - the worst is it wont idle, if it doesnt then youll need to do DATA INIT to do the self idle adjustment (you will loose the tune). the tune is always retained even with power off and unplugged. its only erased if you do DATA INIT

Hey,

I have a RB26DETT FC D-Jetro on its way from nengun and i have the field one touch connecter from greenline. A mate (the_mafia) is re-wiring it to suit my rb20det r32 gtst. He has done the conversion with a normal fc but never djetro.

My current mods

3" turboback

2.5" split dump

GCG Highflow Turbo

Turbosmart boost T

HKS Pod

Walbro Fuel Pump

Fuel Pressure Reg (going to be removed with ecu install)

Splitfire Coilpacks

Plazmaman Forward intake plenum

hybrid fmic

plazmaman piping kit

when ecu goes in (already have waiting)

GTR injectors

3-4" intake pipe

Now we have extablised i can use a vacuume line from under plenum and T off to 2 map sensors. What im wondering is i have read the map sensors need to be spliced into standard loom for airflow meter... so do we cut off plug, and just splice 2 new wires to each existing wire in the airflow meter loom.

Also air intake temp sensor. Where does it go... have been told this will make tune much easier. So basically is there an aftermarket option (bosch) or something that is cheap or should i source one new from nissan?? Will i need to weld any nipples onto piping anywhere or what?

And now for the acc valve. I have a hose going from that to my intake pipe (behind my afm) for now and i have been told i can just put a little breather filter off the valve and leave it at that with the fc... and it will work fine, is this true.

Factory oxygen sensor... should i replace it... i have been told they should be done every 40,000km and my guess is mine is still factory one. I have also been told i wont need it with djetro and it would be a waste of money... in that case can i plug off the dump pipe or should i just leave it or should i replace it.

thanks alot if you could answer these questions. Yes i have read the faq but i could not find too much relating to my issues in depth.

cheers, Leon

:D Help please

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Kinkstah, no, coilovers aren't illegal, especially as a bolt straight in. The illegal part will be if they're altering suspension geometry beyond factory limits, or the ride height is not legal.   Sounds like the blue slipper just didn't want to deal with any later possibility of mods appearing on the car.
    • The problem has always been that coilovers are able to be adjusted, almost at any time, to be too low. Most people who ever get/got defected for/with coilovers were actually afoul of the minimum ride height rule. So the interpretation by cops/inspectors was always that it is pointless to allow numpty to raise his coilovers and get the car inspected/cleared, then just drop them back down again as soon as they get around the corner from the inspection station.  This led to the interpretation that they were illegal unless rendered such that they can't be adjusted (ie, collars welded to the body, that sort of thing). That may or may not have ever actually been the official line, but I'm pretty sure it's not considered to be a solution these days. Coilovers themselves fall under clause 3.2 b of that manual, because they are an "installation of a variable ride height system" and they don't fit the exclusions in that clause (which point to air springs and other pneumatic adjusters). So, as per previous statements, they require engineering cert to be legal on the road. Once you have such cert, provided you do not adjust them outside the height range covered by the cert, you are OK. Without, you have an unroadworthy vehicle.
    • Here E10 is the cheapest fuel. And general advice is to not use it unless you hate your car. From what I remember it clogs up stuff in the fuel system or injectors?  With US/Canada being E10 across the board, does that mean that all fuel there is terrible?
    • Sorry, are coilovers ACTUALLY ILLEGAL in NSW? They aren't in Vic, as long as they retain 70% of stock travel and the car is above 100mm off the ground. Does NSW actually have a law making coilovers actually illegal? RWC/Blue Slip/Engineering people not knowing the actual f**king laws boils my blood. Demand them to point to the documentation that states a coilover is illegal. (it may exist in NSW ) Edit: I checked. They aren't. https://www.nsw.gov.au/sites/default/files/2021-02/RMS-infosheet-light-vehicle-modifications-manual-suspension-and-ride-height.pdf
×
×
  • Create New...