Jump to content
SAU Community

Good Skyline mechanic in Melbourne?

RomkaR31

By RomkaR31,
in Victoria

 Share

Recommended Posts

Roy Grand Master

Roy

Posted
Posted

If its basically std, ie ECU, injectors, turbo then dont bother with tuning. Modern cars with ECUs using MAF dont need to be 'tuned'

My thoughts only, but throw a coolant flush and top up with some new coolant.

Throw a new sump of Mobil 1. Motul etc at it with a new oil filter.

Flush the brake lines with a good fluid, or at least check the colour of the existing fluid. Check pad thicknesses.

Throw a new fuel filter at it, and give the car a run on the dyno to check that the fuel pressure is healthy, actualy by the time your charged for dyno time, id consider replacing the fuel pump with a new one of it currently is using a std pump.

What else, id consider putting some new diff and gearboc fluid in it as well. These arent difficult or overly exopensive things...but id like to do it if i had just bought a new car. Looking at the colour of the fluids coming out also gives you an idea of the health/servicing of the car.

Perhaps clean the AFM, put in a new set of copper plugs. As for tuning it, i love shops that use the term a tune...when i think altering fuel/ignition is tuning, and they are doing no such thing, just charging a healthy sum to service a car

As for a workshop, talk to as many as you can and go to whoever your comfortable with. For this sort of work you just need to be sure that the mechanic is genuine/honest and competent....

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

there is a thread... at the top of this section.

http://www.skylinesaustralia.com/forums/sh...ead.php?t=24324

please have a read through it as it contains information such as that.

cheers - ash

SLYSX Rising Star

SLYSX

Posted
Posted
:bs!:

Agh its King ****whit again aka REDFC/ MinesDats, i find it funny how you bag out chasers and say they dont build there own engines etc, when my brothers SR 180 was rebuilt with forgies there last week by Benny and Brad and if you need confirmation of this, the engine was built right in front of Horus's eyes.

EVONUTS Apprentice

EVONUTS

Posted
Posted

^^^You are not the only one who has seen it. When my car was in for the block and head repairs[don't ask, it was pretty bad] I dropped by unexpectedly on a couple of occasions. The first time I dropped in was about three days after the car came in on a flatbed, and Benny intorduced me to my new pistons. A couple of days later they introduced me to a completed cylinder head, ported to boot. Wednesday the week after I was told to come and collect. Oh that reminds me, I still have to get the pics off of them while they were rebuilding it.

silva33 Mentor

silva33

Posted
Posted

ICE Performance have been very helpful with me in the past. Nigel will take the time to explain any questions you may have.. Im taking my car there next week for further works..

There is a large range of good tuners out there, but my experiences with ICE have kept me comming back without bothering checking other places out.

I have only experienced good quality work with the comfort that if something did go wrong they go out of their way to help out..

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...