Jump to content
SAU Community

Recommended Posts

  • Replies 101
  • Created
  • Last Reply

Top Posters In This Topic

Yeah, still going ahead, just need some of the other people to respond so we have enough interest. I sent PMs to everyone who showed interest, but only have responses from half. Will try and chase up over the weekend.

Cheers

Paul

Ok, the only responses I have so far are:

GTS-t VSPEC, 57mm R33 GTR radiator, 21psi cap, ship to Perth

Gav, 57mm R32 GTR radiator, 21psi cap, ship to Perth

M3X, PWR1480 radiator, ship to Perth

djr81, 40mm R32 GTR radiator, to Perth

sileighty, 57mm R33 GTR radiator, ship to Perth

vspec2, 40mm R32 GTR radiator, ship to Canberra.

If there is anymore interest then please PM me immediately.

Cheers

Paul

GTS-t VSPEC,

I didnt see this earlier or else i would have replied, GTLimited is currently in Dubai on buisness, he left on the 9th and i not sure when he is returning, im sure it shouldnt be too much longer, you are free to do it yourself if you want, but he has delt with them quite allot so thats why he gets good prices, I heard from him about a week ago, I will let him know as soon as he returns but if he hasnt returned by next week then i will let you know to go ahead with it.

Thanks

Zenith

Ok, the current list is:

GTS-t VSPEC, 57mm R33 GTR radiator, 21psi cap, ship to Perth

Gav, 57mm R32 GTR radiator, 21psi cap, ship to Perth

M3X, PWR1480 radiator, ship to Perth

djr81, 40mm R32 GTR radiator, to Perth

sileighty, 57mm R33 GTR radiator, ship to Perth

vspec2, 40mm R32 GTR radiator, ship to Canberra.

legend01, 40mm R32 GTR radiator, ship to Sydney

Sorry for pulling out on the group buy, but I found myself a Race Radiators one but now Iam selling the car! Argh.

Note: Anyone looking for a race radiator radiator 40mm 2nd hand let me know if your poor like me and cant afford a brand spanking new one in the group buy.

=p

  • 3 weeks later...
  • 2 weeks later...

Hey Guys.

The group buy is on, and now open for final orders, the group buy is already underway on another forum with 5 people wanting 15 items so far.

It is open to all PWR products, including oil coolers and intercoolers.

If you want any more information please pm me.

Cheers

Sam

Ok, sorry for any delays in this, but we have a price now, and we're underway.

If your interested then PM me ASAP and get your money in.

I'll PM those who previously registered interest.

Cheers

Paul

  • 4 weeks later...
  • 2 weeks later...
  • 3 weeks later...
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...