Jump to content
SAU Community

2005 NDSOC Drag Day - Sat 28 May - Heathcote


Z1LLA
 Share

Recommended Posts

Hey guys

Just a post to let you know that the Nissan/Datsun Sports Owners Club is holding a drag day at Heathcote Park on the 28th of May (its a Saturday).

Entry is open to all Nissan/Datsun vehicles and you don't need to be a member to enter the event.

There are numerous classes to cater for a wide variety of models, so there is something to suit everyone. The finer details of the classes are still being finalised.

For more information you can email contact(at)mazdarotary.net for an information sheet which will be available in the next week or so.

Thanks!

Ben

ndsocdragday47tr.jpg

Link to comment
Share on other sites

  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

Further info/details:

General Event Information

Date: Saturday May 28

Time: 11am to 4pm

Location: Heathcote Park Raceway (www.heathcoteraceway.com.au)

Costs: $40 To Race, $10 To Spectate

Facilities: The club will be holding a BBQ, although a canteen is also open at the track

Contact Details: Matty ([email protected] / 0414 726 692) or Ben ([email protected])

PLEASE NOTE: In order to allow more efficient organisation of the event, please confirm your entry to one of the above organisers by May 7

Requirements for Racing

Long Sleeved shirt/pants

Helmet in good condition (Helmets are also available for hire at the track)

Radiator overflow bottle

Car must be in safe/roadworthy condition

Passengers must comply with the same requirements as drivers

Class Information

Note: All classes DYO except Top 8, minimum entry numbers apply for each bracket

Classes available:

- Zed Challenge: Two classes - Classic (From 240Z to Z31 300ZX) and Modern (From Z32 300ZX onwards)

- Skyline Challenge (All RWD & 4WD Skylines except GT-R, Turbo and Non-Turbo)

- Silvia Challenge (From S12 through to S15 (inc 180SX))

- GT-R Challenge (R32-R34)

- Race (Open to any vehicle, slicks, race fuel, no exhaust)

- 4WD (Open to all non-Skyline 4WD models)

- RWD (Open to all non Zed/Skyline/Silvia models, Turbo and Non-Turbo

- FWD (Open to all FWD models, Turbo and Non-Turbo)

- Female-Only (Open to all models, female entrants only)

- Top 8 (Open to quickest 8 cars of the event)

Further details on classes and the event information sheets are attached.

Link to comment
Share on other sites

  • 1 month later...

I'm pleased to be able to announce that we have also managed to secure a couple of the fastest Nissan's in the country for this event. Coming over from South Australia are:

Theo Spartalis' GT Autosound S15 Drag Car ( http://www.gtautosound.com/projects2.php?s...section=s15drag )

Keir Wilson's two R32 Drag GT-Rs ( http://www.ausautoportal.com/willall/draggtr.htm )

With just over a month to go, the event is shaping up to be a real treat for Nissan/Datsun fans.

Remeber for more information please email contact'at'mazdarotary.net

Replace 'at' with @ (to prevent spam)

Thanks!

Link to comment
Share on other sites

Ok - who we got so far?

Snowman

R31Nismoid

riggaP

Adzmax

Al (?)

West

Robo's

Leewah - 617rwkw's

PurpleR32 - 535rwkw's (your coming Rosco)

Who else? It's cheaper than Calder and you'll get more runs here.

Link to comment
Share on other sites

you can enter on the day, thats no problem.

Entry doesn't have to be confirmed early, but it can help to organise things a little better and get an idea of the number of cars per class etc... :D

Link to comment
Share on other sites

Ok - who we got so far?

PurpleR32 - 535rwkw's (your coming Rosco)

Who else? It's cheaper than Calder and you'll get more runs here.

heheheh, well if i dont break my box either this weekend or next i will try to get there.

Would be great to run against Keirs car.

It outta my hands and upto the gearbox gods now :headspin:

Link to comment
Share on other sites

  • 3 weeks later...
Guest
This topic is now closed to further replies.
 Share




  • Similar Content

  • Latest Posts

    • Got some decent progress after work yesterday and also today. Got the ECU all wired and passenger side interior all back together. Kept the wiring up nice and high to avoid people standing on it. Got the surge tank relays rewired and tidied up the pump wiring and cut a hole to bring the cables through.  I found a spare USB cable I had lying around so I decided to cut it up and see if I could use it for my CAN 1 bus. Turned out one of the pins I needed was to the shield of the cable so i cut it up and desoldered it and resoldered to the correct pins.  Had the issue with the powersteering hose hitting the A/C compressor and fan shroud. I pulled the bracket off and modified it to remove the front mounting point which now clears it all. Will keep an eye on it to see if theres any signs of fouling once it's up and running.
    • That's some good input mate. Nice.
    • So today I went well outside my comfort zone (again) to replace my valve cover gasket.  I have had a big leak over the exhaust leading to a lot of smoke and smell every time I drove it. The leak was in the rear driver's corner.  The job wasn't hard as such, just a bit finicky and time consuming.  The old gasket was rock hard and broken right where the leak was.  The leaky corner had so much sitting oil in it.  The good news to my amateur eyes was no buildup or sludge under the cover. It all looked fairly nice in there.   I haven't started it yet. I ran out of light and body when putting the coils and injector loom back in. Probs only 30min left for the morning.  I was so nervous putting the cover back on, I must have lifted it 5 times to make sure the gasket was still seated properly. God it's going to be nice to be leak free and not make other traffic light queuers think my car is about to explode.
    • Gave the Mazda it's first wash, it will need some clay, a light compound, and polish polish to remove a few swirl marks, but that will be a job for when I have a full day to get my DA polisher action on
    • Just did this job on my 32 with the boost doc kit. was quite simple to fit, hardest part was getting the rubber bungs back on the firewall. does anyone know how the heater will work now without the flap in the bend? Will I just have a heater on 24/7 now?
×
×
  • Create New...